Jump to content
SAU Community

Recommended Posts

These seem to be impossible to find, I dont care if they are a copy I just want them. They look so simple, I don't understand why no one has copied them by now.

post-32201-0-35482100-1376448357_thumb.jpg

So far I have asked Peter@ Bodyform, JSAI, Just JAP. I only got a response from Peter saying he doesnt have any and would not know where to get them they are extremely hard to find.

Please let me know if anybody has a clue where to find these

Rgds

Andrew

Also very interested in these.. Quick google search and here you go.

Not 100% these are the same..

http://item.mobileweb.ebay.com.au/viewitem?itemId=380694389810

"JDM pods"

Edited by Zrobe

Also very interested in these.. Quick google search and here you go.

Not 100% these are the same..

http://item.mobileweb.ebay.com.au/viewitem?itemId=380694389810

"JDM pods"

No these are not it... These are just the mud flaps... I already have these on the car they come standard

Try:

http://www.importmonster.com.au/

http://irev.com.au/

^^ I think these guys can source OEM Parts

THanks I have rung Import monster and they asked me to send them an email so they can try source it. lets see what happens

THanks I have rung Import monster and they asked me to send them an email so they can try source it. lets see what happens

Yeah good to hear!

Aaron is consistantly getting container loads of parts.

So you can only try :)

They look a bit incomplete and standout because of it.

Personally I like the Trust rear pods that look the same but wrap around and finish just shy of the tow hooks.

They look more at one with the GTR.

Edit: and yes for $250 UAS can supply what your looking for.

Edited by Sinista32

Hi Guys I could not find these anywhere but after so much pictures and comparing with Type M, I realised that some of the Type M that were fitted properly and modifed to suit the GTR body abit better looked good infact I even liked some of them better than the N1 pods. Now After speaking with Pete from bodyform he gave me an Idea and said if it were his car this is what he would do. Now, I am completely SHIT! at photo shop and I dont even have it on this computer, so what I did was use Windows Paint and modified the Type M pods in the way that he explained to me (as best as I could), Of course guys beware this is done on Paint and very rough!

I want you to tell me which looks better, Try picture it from the rear as well I wish I had a rear shot but I dont, so you need to use your head, what better place to be then here people who have seen Many BNR32 from every angle , hopefully you can help me decide.

I have 2 Pictures to compare Side by side, 1 Shot is the Type M Fitted pretty nice and neat, and the other is the modified Type M pod , Dont forget the modified Type M pod was done in paint so it doesnt look as neat but it will give you an IDEA of what Pete was talking about. He said the way he will do it is match it with the body lines of the GTR . One thing I wanna say is that the thing I don't really like about the Nismo's after 100's of photos and different angles and cars, I realized I don't like the curve on the bottom, its too Boxy and also doesnt flow with the lines right , I think the bottom of the Type M is better in that regard.

Anyway Please check and let me know. Please dont say the NISMO because this is out of the picture now so vote only between these 2 - VOTE VOTE VOTE :)

post-32201-0-30496600-1377357166_thumb.jpg

Edited by GTRAAH

the nismo pods :P

I can see where youre going with this.

I prefer the modified as its closer to the nismo pod.

but, the top corner where you would have cut it youve left squared off, id round it, make it look more natural.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...