Jump to content
SAU Community

Recommended Posts

You cant use jumper leads or a jump pack to start a car through a dead/dying battery.

Spark, Fuel, Oxygen (not necesseraly in order)

When you go away you disconnect ignitor and AFM. It's not the first time you have done this.

This time you reconnected Ignitor and AFM (as per every other time). Today it started, idled and then stalled in gear. when you went to leave.

Was it difficult to start or sound unfamiliar ?

Leads me to believe Fuel or Spark. You say the tank is full.

Can you here the Fuel pump prime ? Is there fuel getting to the rail and reg ?

based on the response either the FP is dead or there is not enough power to the pump.

You have Fuel pumping through its veins - Y/N

(Some times you can hit the tank from underneath near your fuel pump and it will work again till next failure)

So moving onto spark

Check again your ignitor and AFM plugs. Dry, good connection ?

You car should still start with your AFM disconnected.

Ignitor - a possibility. But put that on hold for now.

Starter - possibility but these generally wear out (you would know it's coming)

Put a mates battery in - known working. Try turn it over.

Still not working ?

When was the last time you changed/checked your plugs. They can oil up and it's a bitch to start.

Oh and being a manual (no pun intended) this morning you could have tried jump starting down the road.

This can remove a few items off the check list (Alternator, Starter Motor, Battery) to get your car going.

Do anything else before you parked it ?

Edit: Both sides of the ignitor plugged in, is it earthed properly ?

Edited by Sinista32

I disconnect them every time I go away for a weekend. (Heads up to the robbers lol)

The car started the same as it has every day and didn't seem any different.

The only difference was a slightly different note to the idle, however it was sitting fine at 1000rpm

The car rolled as I clutched out and gave it a little revs, about half a meter and this is when it stalled.

I can hear the pump prime and stop like normal so that leads me to believe it would have fuel pressure?

I will have to check about if the fuel is pumping correctly.

Where should I be checking this? My thought is to disconnect the line just after the fuel filter.

The plugs were changed about 10,000km ago and I checked them about 1,000km ago when doing a compression test

(All looked fine bar 1 that had a little oil due to a leaking cam cover gasket, this has been ordered and will be replaced)

I cleaned all the oil from around the area to make sure it does not happen any time soon.

I was worried about attempting a hill start and not being able to get it home if this fails due to the hills in my area.

The car was running fine when I parked it on Friday night.

Edit: No immobiliser and plugs are both plugged in (Heads up to the robbers again lol, I have a shotgun)

dude i can come around with my battery and we can test it out or if that doesnt work atleast two minds will be better than one especially when your almost freaking out you might not be thinking straight could be a very small problem.

it could also be the issue you had with the sealant fr the TB somehow not opening up to let air in. Because you said it started then stalled could be the TB is stuck on the close position. Try starting with your foot down to the pedal a little just enough to open it.

Verms has said he might come around as well.

3 minds are better than one manual haha

Bryce you are more than welcome but don't you live on the North Side?

nah i live in the dirty south. Pretty sure i still remember where you live haha. Been stalking you lately

Not that this is your problem but just to put it out there... If your Battery is too flat, you cannot roll start it.

Check to make sure that little Indian Boy hasn't lost his ball inside your Enginebay somewhere. :laugh:

post-78856-0-51127000-1376899055_thumb.jpg

Okay so the car is still sitting in the driveway and isn't starting.

Bryce came around with tools and Shane (Wilderboy)

-checked the return fuel line and it sprayed fuel everywhere so I checked fuel off the list.

-triple checked the plugs and they were all secure.

-pulled out the spark plugs and they all had fuel on them but no oil.

-plug the spark plugs into the coil packs and check if they had spark, all of them did.

-put it all back together and tried to start it.

No luck it just sits there turning over but not starting.

The ignitor pack on top of cam cover does have a crack through it but the spark plugs had spark..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...