Jump to content
SAU Community

Recommended Posts

Hmmm... I wonder if ECUtalk can connect with a Nistune? I'm guessing yes but I'm unsure.

Try unplugging the ECU and reconnect incase there is a dodgy connection?

Unplug and plug in everything. :D

yeah interesting...seems like the basic checks have been done OK.

it is a standard ECU right? plugging in a powerfc and hand controller might tell you more.

The CAS can fail physically, as can the ignitor so it might be worth swapping both with known working ones. I am near Red HIll today but the stagea runs an r34 cas and no ignitor so I don't think I can help.

It's running a Nistune Chip Duncan.
The strangest thing is it idled and worked this morning for the few seconds until I went to take off.

That's when everything cut out and it just wouldn't start.

Has anyone got an R33 ignitor that I could try unbolting and using?

It's only 4 bolts on the top of the cam cover to remove it :D

I might try the clutch starting idea but I will need to get some mates over to help push it up the hill.

Might try that if the ignitor doesn't work

^^ agreed you have spark but is it a STRONG spark. I assume one of you have a multimeter. Do you have correct volts on ignitor cas afm. Are your grounds good, have you possibly knocked any. Is your solenoid for vct switching correctly (cant recall if your running.it with your nistuned r32 ecu)

obviously start small and obvious but if its just coincidence and there is an actual fault. A multimeter can tell you a lot ecu talk even better if possible.

Didn't change the battery Sin because it had plenty of power to crank the engine about 12 times.

Not sure if that's a mistake and I should have done it anyways.

I haven't got a multimeter so can't test voltages.

I wouldn't know what voltages to expect from each part either.

Does anyone know if ECU talk works with Nistune?

btw when you say you have to push it uphill to clutch start it, is that because your house is right at the bottom of a hill? because you can clutch start in reverse too. If you are careful (clutch and brake as soon as it fires) you can even do it in your driveway, it only takes a couple of klm/h to start a car.

ecutalk should show most of your ecu values and voltages on a PC which can help with spotting a dodgy sensor like an AFM or TPS (by voltage) or even CAS (by seeing fluctuating voltages)

Yeah I have a really steep small driveway that's at the bottom of a hill.

So once it's down the driveway then there is no way I would get it back up there.

Also it would mean leaving the car at the bottom of the hill and pretty far from sight/sound

I would love to roll start it Duncan but it would probably be last resort unless I had some rope to tow it haha

Rob can I come pick it up tomorrow arvo from you?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...