Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

I'm at work, work is boring and through photosynthesis I am boring as well....

I am not convinced that is the correct use of photosynthesis.

I don't think think using radiant energy to turn carbon dioxide and water into carbohydrate is the cause of your being boring. Though according to Ants you are green so maybe you do photosynthesise

I hate everyone having breakfast and days off... Stupid me even said yeah no worries I will do a full day Saturday before working Saturday night at my other job, that's what I get for agreeing to shit when I am having a good day!

I am not convinced that is the correct use of photosynthesis.

I don't think think using radiant energy to turn carbon dioxide and water into carbohydrate is the cause of your being boring. Though according to Ants you are green so maybe you do photosynthesise

LOLZ

4th fishies down the freeway! ensure to upload vid for lolz

2nd half throttle slide off a round about and up the street (couldn't hit the hammer due to traffic) he went very quiet

I am not convinced that is the correct use of photosynthesis.

I don't think think using radiant energy to turn carbon dioxide and water into carbohydrate is the cause of your being boring. Though according to Ants you are green so maybe you do photosynthesise

What are u on about, photosynthesis is the process of photographing synthesisers in your spare time.

elGXEwf.png

VhsY0AQ.jpg

How could you not know that, youre a sound engineer you deal with this stuff every day... And twice on weekends when you photograph your German folk band zeig mir die Müsik

  • Like 1

What are u on about, photosynthesis is the process of photographing synthesisers in your spare time.

elGXEwf.png

VhsY0AQ.jpg

How could you not know that, youre a sound engineer you deal with this stuff every day... And twice on weekends when you photograph your German folk band zeig mir die Müsik

bahahahahahahahha!

Quick snap shot from Zeig Mir Die Müsiks last gig they played at keine krähte hier arena in woodford, not bunts well developed beard (it's a fake of course but no one needs to know he can't grow facial hair)

EAvYYhH.png

I spoke to Sean this morning.

The Ant-Eater went back on the dyno - everything going well

An hour after being on the dyno - Hatlech decides to shit itself

:( aww not good bro

Alledgedly everything is still running but the USB port slows down and Sean cant get any proper reading from it.

Haltech was sent back to Sydney yesterday (hopefully will get it soon) to have a look at it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...