Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Zac is a top bloke, went down and found that I need:

Rear main seal

Top radiator hose - Got this thanks to Zac I will fit it when the car cools down.

Gearbox leak fixed - little leak @ the back.

Cold motor was the cause of the missfire I will run the factory coils until I cbf swapping the yellow jackets back in again.

Zac is a top bloke, went down and found that I need:

Rear main seal

Top radiator hose - Got this thanks to Zac I will fit it when the car cools down.

Gearbox leak fixed - little leak @ the back.

Cold motor was the cause of the missfire I will run the factory coils until I cbf swapping the yellow jackets back in again.

Zac our trusty little handy helper :)

Great to hear mate. I'm pleased to hear it wasn't anything major.

Means you can have a bit of driving fun once repaired ;)

Oh and Clint, with that hose fitting just make sure there is no crap on it and no coolant is on that sealant

It's ok if like a drop or 2 but it's best to have it clean

And let that sealant sit with the clamps on for a good hour before any coolant is put in the system, just for the extra sealing strength

Zac our trusty little handy helper :)

Great to hear mate. I'm pleased to hear it wasn't anything major.

Means you can have a bit of driving fun once repaired ;)

Didn't stop me from having driving fun, was being gentle on the way home though.

Could of been really bad so big thanks to Zac.

Oh and Clint, with that hose fitting just make sure there is no crap on it and no coolant is on that sealant

It's ok if like a drop or 2 but it's best to have it clean

And let that sealant sit with the clamps on for a good hour before any coolant is put in the system, just for the extra sealing strength

Aye will do, DOn't need to drive it again today.

Will head out in the next hour to sus out the car situation

Let me know if you want company

Would u like me to keep this for you Clint just in case u need a replacement straight pipe?

attachicon.gifImageUploadedBySAU Community1382669749.679649.jpg

:P

May come in handy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...