Jump to content
SAU Community

Recommended Posts

Depends on your paint skills and expected results!

If it's say in the engine bay or under the boot lid and you're not too fussed about a factory appearance then definately do it yourself. If it's part of a large panel (around rear window or some other fiddly bit) then I would probably take it to a good panel beater that will cut it out and repair it properly, not just bog over the top of the rust and repaint it.

Again if it's not too bad you may be able to do the prep work yourself and just get it repainted by someone else. Might save you a fair bit of cash that way. If you've got a welder it's surprising what you can do. I've welded a fair few sections into my Datsun and it is surprising what result you can get with some patience and steady hands.

Yeah it's above drivers window and couple smaller ones down the rear quarter window the only rust it has.

Deffinatelly will have to get someone to do it as window may have to come out also.

Do you know any product that will make it stop rusting in those spots?

Cheers ewan

There's some incredibly good rust removing compounds available for surface rust. 3M do a good product, there's another one I cant remember the brand name but Super Cheap sell it (in a small black plastic container with a handle on top, like a mini oil container).

You put the compound on the rusty bit, leave it for 10 minutes, wipe it off with prepsol (oil and wax remover) then with a damp cloth. Repeat if needed. Provided the rust isn't too deep it works awesome. I did a fair few spots in my car (plenum chamber near bonnet hinges, under the boot seal and behind the inner guard liner. Came up pretty good. Provided you either paint it, treat with a rust inhibitor or fish oil, it should keep the rust away in future.

It's a constant battle!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...