Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

gtrGhosTDoGG11

The solenoid on its own is pretty much useless without the controller when it was running on my 33 it had no controller and ran my car at standard boost 7psi thats with filter and exhaust.(it comes with wiring harness lead to the controller)

voityR33

If you give me your address and details i will cod to you.email me :)

Kor'axis

Its exactly the same as the one in the picture brake light works and all (cars in it's not mine).I may allready have a buyer for this ill keep you posted on it.Not sure mspec one maybe.

Email [email protected]

Link to comment
https://www.sau.com.au/forums/topic/43383-r33-parts-fs/#findComment-903746
Share on other sites

Its not mine its another members pic of their car that i got from the gallery just to depict what my wing looks like.

It looks a bit like a r32 gtr aftermarket copy side skirts and a 400r rear bar a bit thoough to me put onto a r33.

Link to comment
https://www.sau.com.au/forums/topic/43383-r33-parts-fs/#findComment-904369
Share on other sites

thanks for letting me use it in my explanation of a stock rear spoiler.HKS-R33

sUPP GDAWG The solenoid on its own is pretty much useless without the controller when it was running on my 33 it had no controller and ran my car at standard boost 7psi thats with filter and exhaust.(it comes with wiring harness lead to the controller)I DONT KNOW WHAT YOU MEAN BY TWO STAGE BOOST?ELABORATE PLEASE.

its a smooth approach to full boost and stays there all the way it feels good.But if you want to be able to use the solenoid go into the wanted or for sale and start looking for profec A controllers being sold separately on their own.I have seen quite a few for sale on these forums they shouldnt be to hard to buy.The solenoid needs new filters and i suggest that you get someone to install for you or get a profec A manual (u can get off the net) which will have install and operating instructions and do it yourself.

im keeping the heat sheild for the moment i think that i still need it for blue slip sorry to the dude who wanted it i would have emailed u but i erased your email by accident.SoZz

:rofl:

Link to comment
https://www.sau.com.au/forums/topic/43383-r33-parts-fs/#findComment-908070
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...