Jump to content
SAU Community

Relocating From Sa Where To Get Rwc And Mod Plate?

DJ-Static

By DJ-Static,
in Queensland

 Share

Recommended Posts

DJ-Static Collaborator

DJ-Static

Posted
Posted

Hi Everyone,

I'm relocating from SA to Springfield Lakes. Can you help me with a suggestion of where I should go for a RWC and mod plate?

In another thread I was told my car looked low and that the cops would pull me up straight away. I believe my car is standard height and it's the illusion of the kit that give it the appearance of being low.

Here are the photos I took for the transport company

post-59520-0-56526600-1383355677_thumb.png

I can get 2 fingers in between the tires and guard front and rear. Is it too low?

Any help would be appreciated.

Cheers.

PWND Grand Master

PWND

Posted
Posted

space between guards and tyres is not an issue, as long as the lowest point of your car (including the exhaust just near the diff) is above 100mm

What parts of the car need to be mod plated?

DJ-Static Collaborator

DJ-Static

Posted
  • Author
Posted

space between guards and tyres is not an issue, as long as the lowest point of your car (including the exhaust just near the diff) is above 100mm

What parts of the car need to be mod plated?

Everything is above 100mm (when checked on level ground)

I have no idea what needs mod plating (because I'm not familiar with your regulations)

My list of mod are:

Secured Apexi pod (not in a box)

z32 AFM

hard suction kit

T04 Turbo

Stainless ext. manifold

Turbo back ext. with hi flow cat etc. Not loud

Manual boost controller (22psi)

FMIC (metal was cut to accommodate the piping to the throttle body)

After market BOV that is 100% recirculating

Q45 Throttle body

Freddy forward facing intake manifold

1000cc injectors

Top feed fuel rail

Turbo smart FPR

Walbro pump

RB20DET ECU with nistune, running E85

permanent wideband lambda, boost, temp gauges to DLP-I08 and Consult

I think that's about it

Cadmoon Grand Master

Cadmoon

Posted
Posted

You will need a mod plate for the turbo at the very least and the hole for the FMIC will probably need to be certed as well, as for the rest I'm not sure. The reo being cut will be a defect if it is found and can't be mod plated.

I know of a mobile mod plate guy on the northside but I'm not sure how far he roams to plate cars. As everyone said keep your SA rego until you have everything up to scratch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Piggaz
      Borg Warner EFR Series Turbo's V 2.0

      By Piggaz · Posted

      A few things that seem a bit off here. - why is there 2 BOV’s?  - the turbo smart BOV on the compressor housing, is it turned up ALL the way? I have seen this become an issue on old man Pete’s car. It would push open and recirc, turbo speed would rise and the boost pressure would do weird things. - stock head? Does that include springs? - tried a different MAC valve? Is it plumbed correctly?
    • GTSBoy
      Borg Warner EFR Series Turbo's V 2.0

      By GTSBoy · Posted

      Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Wow, i wish i found this sooner.
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
×
×
  • Create New...