Jump to content
SAU Community

Wtb Complete Rb26 Head, Intake Manifold And Engine Loom

gold-3lt

By gold-3lt,
in Wanted to Buy

 Share

Recommended Posts

gold-3lt Enthusiast

gold-3lt

Posted
Posted

As the title states, i'm looking to buy a complete rb26 head to build a 26/30. must be in good condition and come with all covers, also after a standard intake side to suit and the engine loom. don't want or need the exhaust side. Brisbane sellers preferred but will buy interstate if the deal is right from a reliable seller. May also consider complete rb25det neo engines. 0433 559 722.

R32GOJIRA Mentor

R32GOJIRA

Posted
Posted

I have a standard (albeit pink, could use a repaint) plenum, throttle bodies and balance tube.

Would be after $800 for the lot plus postage. Located in Wollongong NSW.

I also have a standard RB26 head, but it has a slight indentation on the mounting face on no.6 cyclinder.

Dont know if it can be filled in and then machined flat, as i havent had the time to enquire about it.

It is complete, just dont have the covers for it. But it will need a service anyway as it has been sitting in storage for a long time.

gold-3lt Enthusiast

gold-3lt

Posted
  • Author
Posted

Thanks for the reply mate but i have already found a couple that i'm looking at. one complete running top end minus turbo's $1500 and another low k top end minus covers for $1300.

Your head probably can be fixed. I have a rb25det neo head here thats like that but worse. not game to use it though. Had enough stuff arounds with this build.

pauls Rising Star

pauls

Posted
Posted

In melb & have a 33 rb26 complete motor minus injectors & loom snipped so no injector connectors either.

Block needs bore, but haven't taken head off.

pauls Rising Star

pauls

Posted
Posted

block needs a bore but you havent taken the head off? did you inspect by remving sump and crank?? how many k's and how much?

I cant confirm klm's.

mechanic used some fancy tool to look at the bore.

Chasing around $1800, however can vary depending on what bits you want.

R32GOJIRA Mentor

R32GOJIRA

Posted
Posted

I still have the intake side, plenum, throttles and balance tube sitting here mate if you need it.

  • 2 weeks later...
gold-3lt Enthusiast

gold-3lt

Posted
  • Author
Posted

Bump. Still after a mint condition head as I just got ripped off alot of money by an upstanding member of sau who thought it would be a good idea to lie through their teeth and sell me their lump of scrap metal. Only need a complete head now. no manifolds. Don't even think of trying to palm off your rubbish to me. I need a head in perfect condition. stock or built. Photo's and receipts have preference as do QLD sellers. Contact me if you are a genuine seller. Pieces of shit need not apply.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...