Jump to content
SAU Community

Compression Test

morto86

By morto86,
in General Maintenance

 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted (edited)

On a warmed engine with all sparkplugs removed, with accelerator fully depressed and a charge on the battery capable of cranking the motor at 300rpm.

RB20DE/T/26DETT

New = 170psi

Low Limit = 128psi

Max cylinder difference 14psi

...from engine workshop manual.

Edited by Missileman
Ben C34 Grand Master

Ben C34

Posted
Posted

I just got the reply 210. Cold. Does this mean the head has been shaved previously

No as the comp ratio doesnt effect the compression test. it just ensures the rings and valves are sealing as they should.
Ben C34 Grand Master

Ben C34

Posted
Posted

Def 200 all round with snap on gauge and warmed engine. With researsh this proves the comp ratio therefor is 10:1. As for the knob who said the comp is not relayed to the ratio. Actually write out the equation.

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)

Well personally I would have though it was obvious that the higher the compression ratio the higher the expected compression test result . The value of the compression test for measuring wear depends on knowing the original compression so as above if the stock factory figure was 170 psi then yes 130 psi indicates a lot of wear which can be confirmed with a leakdown test. My engine had 130 psi compression when built because of the choice of pistons (CR about 8:1) and leakdown test is within limits at 5%

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Thanks mate.
    • TurboTapin
      Crank Motorsports Front Axles

      By TurboTapin · Posted

      I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...