Jump to content
SAU Community

Recommended Posts

At the moment I am running my catch can with pcv so rockers tee into the catch can then other port goes from catch to intake but I want to go atmo now instead. What happens if you run same setup as I have now except replacing the line from can that goes back into intake with just a breather? From what I read most choose to delete the pcv when going atmo does it make a difference if you keep it?

Link to comment
https://www.sau.com.au/forums/topic/435882-atmo-catch-can-with-pcv/
Share on other sites

because you have to if you're running an AFM, if you're running a MAP sensor go for gold also the reason for deleting the PCV is to reduce foreign air and other shit entering your motor without passing through the air filter.

Remember the PCV will "suck" air during idle

Block it and avoid the engine sucking in oil vapour is the main reason.

If your "breather" on the atmo can is a mini filter, the air in the cam covers is "filtered" but full of all sorts of vapours that most people don't want in their engine for performance reasons.

The PCV only opens under vacuum, so it has no adverse effects on the engine if it inhales oily air at idle. If it did, the engineers would have found another way to achieve the result, which is to reduce emissions of engine gasses to the atmosphere.

Oil in the intake stream is only a problem under load, because oil is a serious octane reducer.

To the OP, if it ain't broke, don't fiddle with it.

The PCV only opens under vacuum, so it has no adverse effects on the engine if it inhales oily air at idle. If it did, the engineers would have found another way to achieve the result, which is to reduce emissions of engine gasses to the atmosphere.

 

Oil in the intake stream is only a problem under load, because oil is a serious octane reducer.

 

To the OP, if it ain't broke, don't fiddle with it.

i see your engine doesn't enter vacuum on gear shifts... Or need high octane fuel the moment the throttle is jumped back on after a gear shift...

Ive ended up blocking and going atmo, my main reason for doing this is as a test as I cant figure out why my intake and cooler is getting oil in it as turbo seals were checked are 100 percent fine and breather lines and catch can are empty so with this I can eliminate another option as to where the oil is coming from.

Ive ended up blocking and going atmo, my main reason for doing this is as a test as I cant figure out why my intake and cooler is getting oil in it as turbo seals were checked are 100 percent fine and breather lines and catch can are empty so with this I can eliminate another option as to where the oil is coming from.

did you have any sort of mesh or baffling in your catchcan?...a pipe in. pipe out catch can with no internal baffling will do nothing and oil will just end up in your intake again....get a stocking and fill it with coarse steel wool , put it in your catchcan and make the inlet hose go to the bottom of the can while the breather hose exits the top...so that way the vapous re filtering through the mesh on the way up and this will cath most of the vapours..and your can should fill with oil instead of your intake

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...