Jump to content
SAU Community

Recommended Posts

Hi SAU

I've had a recent issue with my R32 GT-R in regards to the vehicle not starting.

The situation is that I parked the car in the shed and threw a cover over it. Upon returning two days later to take the car out for a drive, it simply wouldn't start.

The starter motor does turn over, the fuel pump primes when the key is rotated to the ignition barrel and there are no fault codes being identified by the ECU. It just won't turn over and start. I have dropped the fuel, threw the battery on a trickle charge and tried a few days later but to no avail.

Any insightful information to direct me to the cause of the problem would be much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/436817-r32-gt-r-not-starting/
Share on other sites

I'd try another battery. Trickle charging a faulty battery is a waste of time.

+1 and batteries can do funny thnings when old or dying, could be enough charge to crank but not enough for fueling and/or ignitionn etc..

Check you earth lead, make sure its grounded properly to the engine/chassis..

I once spent a week chasing what i thought was a dead starter, it turned out being that i needed to remove the ground leads everywhere and sand all the points.

Boy did i feel like a useless carnt after working that one out.....

I've tried 3 batteries, all to the same result. Although, the newest one did sound like it was the closest.

PaulosECR33; It doesn't try to fire at all, starter motor just keeps turning over to nothing.

I'm going to change the plugs and fuel filter at some point and have another crack.

I'll also have a look at the earth leads and make sure they're all in order.

Will report back with any new developments but don't hesitate to keep bouncing ideas off me.

Take off the cas and turn it by hand with ignition on. should be able to hear the injectors firing, and pull a coilpack off abd check for spark at the same time . They should give you more info as to what the prob us.

it is worth trying this old chestnut right now because it can be the issue (I know from experience - today!)

Ignitor - swap with a friend who has one. 5 minutes will rule it in or out :thumbsup: and is the easiest thing to do

need a 4mm allen key and 5 minutes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...