Jump to content
SAU Community

Compression Help!

evoeta

By evoeta,
in Engines & Forced Induction

 Share

Recommended Posts

evoeta Apprentice

evoeta

Posted
Posted

Hey guys, this is the first rb30det ive tridd to build. Its a fairly basic one. Stock bottom end with acl bearings, standard rb30 rods and pistons which are in good order. Arp head studs. 1.3mm headgasket. and rb25det head which had been cleaned up etc. Went to to compressio test. It had no extractors, intake on and no spark plugs in any of the cylinders prstty bare and im getting about 100psi all over roughly. B

Just did the test with battery on starter motor etc any help much appreciated!!

Link to comment
https://www.sau.com.au/forums/topic/436963-compression-help/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Sounds like my engine. Unless you're going to pull it apart and put in some high compression pistons you may as well carry on and test it again when its been run. Thinner headgasket would help but will not make a significant difference. My compressions are all around 120 and I am making 314AWKW with a 3540R. PM me your no and I'll give you a ring if you want.

Duncan Grand Master

Duncan

Posted
Posted

absolutely don't worry about the compression until the rings are bedded in. and for what it's worth the motor should be warm too, as well as a healthy battery (which they normally aren't by the time a motor's been pulled out, rebuilt, and put back in)

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Tein Circuit Master- rebuild worth it?

      By MBS206 · Posted

      If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • MBS206
      Best place to order Authetic R32 Parts in Japan

      By MBS206 · Posted

      Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • MBS206
      NC MX5

      By MBS206 · Posted

      Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • MBS206
      Blue slip

      By MBS206 · Posted

      I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...