Jump to content
SAU Community

Recommended Posts

I know there has been a few people asking this but I havnt really found a straightforward answer

I have a 98 r34 gt25 and I want to upgrade it's brakes on a budget (as I am only a first year aprentice)

What model skyline brakes will be a direct bolt on or if there not what brakes will fit with an adapter front and rear

Also should note I'm running the factory nissan alloys so would have to fit inside there

Link to comment
https://www.sau.com.au/forums/topic/437424-r34-gt25-brake-upgrade-help/
Share on other sites

Witch model exactly tho

R34 Gt-t.

Runs 310x30mm rotors with 4 piston Sumitomo Calipers on the front, and 296x18mm rear rotors with 2 piston Sumitomo calipers. The rears are identical on R32,R33 GTS-t and R34 GT-t.

The fronts use 14mm mounting bolts, whereas the (similar looking) calipers for the R33GTS-t use 12mm mounting bolts, and also run a 296x30mm rotor. You can use a sleeve in the bolt hole but the pick is the GT-t caliper.

Ask any import wrecker, they will know what these are. You should be able source the front for $300-$400 with serviceable rotors. The rears will be half that, or less.

If you need rotors or pads; GSL Rallysport have some excellent, and well priced options.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...