Jump to content
SAU Community

Recommended Posts

Hey guys me and the missus had a really good time today. Great people, great food and atmosphere, definitely looking forward to the next one!

Couple photos from the day, sorry some are blurry. We tried to take as many rolling shots on the Highway, kinda diffucult driving all over the place catching up to people lol.

LGKmMMJ.jpg

Po2QZzU.jpg

nxTYfhW.jpg

KvOuaxu.jpg

DGMd9Dj.jpg

60m2ZbS.jpg

NUL5gg7.jpg

SVi5aQK.jpg

EMrSmSF.jpg

bMxYqKd.jpg

nNdEd1Q.jpg

OW2l6xD.jpg

9RjnCvY.jpg

r9OHIpa.jpg

GYvmp9a.jpg

L6DiJnm.jpg

YVRI2Bn.jpg

PCHPxp2.jpg

  • Like 1

Great day, our little boy Enzo enjoyed the day out and seeing all the cars. Some very nice photos too, love the rolling shot of our R35 :)

Maybe one day we can arrange a lunch at one of the winery's will see if we can get permission to park the cars in the vinyards for a good photo shoot.

Awesome shots. Glad everyone enjoyed the day. Looking forward to seeing everyone again

If the next one is on a Sunday as well I have the day off. Managed to twist the bosses arm from working straya day ;)

Can't wait for the announcement James

What was really scary yesterday was that whilst waiting (in lane 1) at a red light on Orange Grove Rd, just 200m up from the Liverpool Meet Pt, this woman came racing down through the same red light at about 80 clicks (in lane 2).

She had to stop behind traffic at the next lights as we were about to turn left to KKs.

She appeared to be talking on her mobile.

Dave said, "We nearly witnessed a death!"




  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...