Jump to content
SAU Community

Alloy Airbox. Eoi

Trex

By Trex,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Trex Grand Master

Trex

Posted
Posted

Some of you might remember I had those deflectors re made for people using the std cooler and intake. About a week later I installed a front mount and pod and that was fine in winter. Now that it's coming into summer I needed to find a way to keep intake temps cooler. So I've come up with this airbox, I like this one better than any other one I've seen (I'm not biased at all) I'll be using the hole left over from the cooler return under the box to run some pipe to the lhs front grill for cold air.

Would anyone else be interested in one?

And what should I change to make it better/looks nicer?

Also is cardboard flammable? I might use alloy like the deflectors

post-108100-0-19533500-1389858981_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/437690-alloy-airbox-eoi/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Yes cardboard is flammable.

Aluminium would be fine. Some people use Perspex which you can bend with a heat gun.

Or you could use one of your deflectors with the stock airbox and maybe run some extra air into the airbox from behind the headlight.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Lol thanks bob. I'm really keen to get some alloy and cut one out

Something like this? It's going to cost too much to get one made I think.

Yep you can get quite thin aluminium which is easy to bend and cut with some tinsnips or a nibbler if you have or can borrow one.
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

I was kidding about the cardboard part guys haha

I'm going to use 0.8 like the deflector. No way would I use tin snips, I was thinking maybe a jigsaw with fine teeth or a dremel or a die grinder?

A while since I did some metalwork but I think for soft metals such as aluminium you need coarse not fine teeth. This is a nibbler - they are quite expensive or you can (like I did) get a cheap attachment that goes in an electric drill from a store such as Bunnings:

http://www.makita.co.nz/products/detail.lsd?item=JN1601&-session=Makita:7694CC8C02dc220C0EsKHxACAECB

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

That looks pretty good! Thanks bob!

I made these a while ago and I'm just throwing up pics now because I'll get it done soon. Here was another intake I made, but they're going to be way too much effort for my skill level

You've done all the hard work. Just flatten out the cardboard and draw around it ...cut out the shapes and then bend!

Trex Grand Master

Trex

Posted
  • Author
Posted

I'm not too sure yet glyn. I was thinking about that last night,

It really depends on what people think they're worth, as it really is just a top and side piece that is put together by 3 small L brackets, and it is not fully enclosed (it looks it, and almost is). I will still like the look of this better than any other one Iv'e seen for sale.

I'm guessing anywhere from $80? It will take around 2 hours to make, and the cost of picking up the goods and the goods themselves. But I personally don't think too many people will buy one, if someone wants one i will make it.

I've just found some rubber edging. and the exact same bolts that are used on the deflector, so it will tie in perfectly. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...