Jump to content
SAU Community

Recommended Posts

  • Replies 293
  • Created
  • Last Reply

Top Posters In This Topic

Not for a while. We are going to give it the rwc inspection today, but not writing it out untill I have enough for rego so I can do it on the same day, and also I need to get past this transport issues, and then we will be good

Thought I should update

Should be taking the car up home today, have been selling bit of stuff. And helping #@Matty95 with his 31, and helping another mate look for 32's

So in the next few weeks I will be saving up for some new bits :) I'm in no means of a rush to get it regestered or me behind the wheel again, but I do have to pass a few obsticles with transport before I can.

So the thirty is off the cards. That won't be happening for a long time/ever.

I thought I already have the bits I want for what I wanted to do. Except the highflow now :/ oh well.

Have also ordered a few suspension bushes and stuff, new bit of kesh will be going on misc. engine stuff, like the cas grommet, tappet covers gaskets kit, probably some silicone joiners and new clamps, and another good service

  • 2 weeks later...

post-108324-14006695350782_thumb.jpg thats the only photo I took. But I will take more tomorrow

Dropping it at the place tomorrow at 7.30 am for a wheel alignment and balance

Trade prices are best ;) only cost me 80 for the ball joints and 50 for the wheelie tomorrow

Part number is in the pic ;) they worked well went straight in. Touch bit bigger but makes for a tighter fit. No chance of popping out now.

Still waiting for that call.... I have rego papers in my hand ready to go.... But I need the car....

  • Like 1

Surrogate vin apparently means because import it has been given a new number so it's a surrogate

But I did find out some other info on the car that is bad but does not affect me or the car

If you want to know text me :P

Surrogate vin apparently means because import it has been given a new number so it's a surrogate

But I did find out some other info on the car that is bad but does not affect me or the car

If you want to know text me :P

ok

Installed footwell lights again today. Was going I have them switched but the mini switch was dead. So I will have them set up to come on when the ignition halo is on. And I will also have them come on when Parker's are on. And have it switched ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...