Jump to content
SAU Community

Recommended Posts

  • Replies 293
  • Created
  • Last Reply

Top Posters In This Topic

post-108324-14017201756885_thumb.jpg

post-108324-14017201925421_thumb.jpg

Sorry about the gold tinge to the second pic it's my case.

So that's just the bias it set up a t10 holder cable tied into place. Wires run from both and joined into one cable

+from car goes to a fuse then switch then out of the switch goes to the 2 lights then back to single wire and earth.

+

-----|_|---/_----/-------0--\______ -

\_____0__/

  • Like 1
  • 2 weeks later...

Got my exemption :D so happy that I ca drive it again.

Car is booked in for an alarm install with chris Rodgers :)

Should go nowhere after that :P

Going to take it out to happy laps this weekend and maybe put in out on lakeside and se how it goes. That's a big maybe

Window motor and reg is in. All works. Took the car out to lakeside today and watched the happy laps :)

Got home and figured out a way to pump up my rear left tyer (valve is to short in the gtp's so I have to get a valve extender) had to use a bike pump.

And sold car parts to nick (#@Captain Natro) and another guy :P

Glad you've finally got the exemption through! Bring on the fat lapping....

Clear side indicators look so much better. I remember I first bought tinted ones and thought they were ok, but then once i got the clear ones i realised how much better they look!

Whats next on the modifying list Zac or just some enjoyment for now?

I have had my enjoyment in the past few weeks. I'm going to out my 4.11's back in the 4.3's are a bit crazy. I'll keep them for skid days :P

Then after my alarm install I will be looking for sway bars and bushes. Later on shocks and springs :)

Theeeeennnn

34 turbo and fmic piping or intercooler kit, fit the intercooler and leave that for a bit. Then I will be highflowing turbo and fit that and send the Ecu off to have the mods down to suit r33 and once that's done is done I will get base map. Install it amf and 34 turbo and then send it off for tune

This last step will be in the last 3 months of p plates and just leave it sit till I'm off them

So the next few little things I will be doing. I will be installing a volt guage.

Disabling the speed lock on the passenger side.

And take this window regulator back out and switch the motors. This one dosnt line back up properly so it is going to tare my seal. I do not want that haha

Put some new bolts in the guards and headlights and stuff will post pics tomorrow

Had one of the gtp's go flat on me today, the valve is leaking through the seal. So I went and got some tyers put on my stock rims today and I will put them on tomorrow photos to follow

post-108324-14050065359355_thumb.jpg

Stock tyers on the rear

post-108324-14050065622773_thumb.jpg

Why the wheel was leaking

post-108324-14050065829373_thumb.jpg

tire being re-fitted

And didn't get any photos of the guard bolts but will do tomorrow

This thread used to have a lot of interest :( it was motivating me :(

Quiet disappointing to see it all go away

And the worst part is you guys are missing out on this

post-108324-14050067004632_thumb.jpg

Trust return flow intercooler got it for $150

post-108324-14050067252279_thumb.jpg

Straightening fins

post-108324-14050067542742_thumb.jpg

painted black looks gloss but dries matte. It's drying over night and tomorrow I'm painting a

post-108324-14050068277851_thumb.jpg

In red

post-108324-14050068501559_thumb.jpg

Got them all cut out will just be spraying it on tomorrow

And re painting the pipes black

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...