Jump to content
SAU Community

Recommended Posts

so i bought another coupe

IMG_6699.jpg

IMG_6700.jpg

IMG_6701.jpg

IMG_6702.jpg

IMG_6703.jpg

IMG_6704.jpg

i have a shed full of r31 shit I need to use so his is a decent excuse

IMG_6715.jpg

after

IMG_6716.jpg

rims

sparco ds2's

18 inch by 9 +10 and 10 -16

depending on how they fit i may get the barrel bros to beff up the lips

ts_auto-img600x450-1349701396juwmip56999

ts_auto-img600x450-1349701396pgdc9b56999

tidy up the front end

image_zps958312a4.jpg

Just need to cut the ic duct

image_zpsf7e1b4fc.jpg

Also the canards are done

cause all the kids dig these

image_zpsd1e44bf0.jpg

front flares

image_zps2457054b.jpg

image_zps282611b5.jpg

image_zpsd0c4976e.jpg

image_zps35e10562.jpg

image_zps3418ebb0.jpg

ive been slowly gathering parts for this pos for about 15 years

Decided this old girl would get a early 90's turbo kit to look cool

So bought this old school kkk t3 twin kit for the gtr motor that's going In

image_zps9b046f81.jpg

image_zps71bc26f9.jpg

image_zps67e7567d.jpg

i then bough a good running rb26/30 with a tomie head

procam ect

and i mounted the Turbo kit

all mounted up ready to party

turbo3_zps0e87b9f8.jpg

turbo2_zps2ff67a42.jpg

fiberglass boot with n1 lip

DSC_0060_zps486c4c38.jpg

DSC_0061_zps6c21a958.jpg

i should have the front guards back soon

DSC_0062_zpsd706ccb6.jpg

randys old rear end

DSC_0069_zps5f39c7f6.jpg

new rear end, has been modified to make it faster

DSC_0070_zps9b12c2e3.jpg

new struts

DSC_0071_zps88c882ab.jpg

DSC_0073_zpsf38dbb41.jpgcant decide if i should run bonnet pins for the boot or shlap the key in?

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0072_zps65be6328.jpg

old ghay arse 8 port hr31 rack out

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0075_zps3216550b.jpg

new flashy( least now i can see the oil leaks)

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0071_zpsf46ae62d.jpg

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0074_zpsec30b79e.jpg

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0072_zps8c04c3e6.jpg

new front struts

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0070_zps2c9dc665.jpg

so some more progress

dummy fitted the engine box and turbos

to do so had to pull the turbos off

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0076_zps5112a893.jpg

then slapped the motor and box in

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0080_zps45acdff0.jpg

http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0079_zps420e163e.jpg

turbos were fine

front dump pipe was fine

rear dump pipe fowled on the firewall at the expansion joint, was expected as the 3 litre is 1 inch taller and it just touches.

will give it a massage

besides that r31 are heaps larger than gtrs so there was a fair bit of room to move

http://s236.photobucket.com/user/fatzgtsr/media/r31%20coupe/DSC_0083_zpse6cc78ac.jpg.html"]http://i236.photobucket.com/albums/ff9/fatzgtsr/r31%20coupe/DSC_0083_zpse6cc78ac.jpg

Link to comment
https://www.sau.com.au/forums/topic/439212-spare-time-31/
Share on other sites

I like how you gave up with the image links towards the end.

cant decide if i should run bonnet pins for the boot or shlap the key in?

DSC_0072_zps65be6328.jpg

old ghay arse 8 port hr31 rack out

DSC_0075_zps3216550b.jpg

new flashy( least now i can see the oil leaks)

DSC_0071_zpsf46ae62d.jpg

DSC_0074_zpsec30b79e.jpg

DSC_0072_zps8c04c3e6.jpg

new front struts

DSC_0070_zps2c9dc665.jpg

so some more progress

dummy fitted the engine box and turbos

to do so had to pull the turbos off

DSC_0076_zps5112a893.jpg

then slapped the motor and box in

DSC_0080_zps45acdff0.jpg

DSC_0079_zps420e163e.jpg

turbos were fine

front dump pipe was fine

rear dump pipe fowled on the firewall at the expansion joint, was expected as the 3 litre is 1 inch taller and it just touches.

will give it a massage

besides that r31 are heaps larger than gtrs so there was a fair bit of room to move

DSC_0083_zpse6cc78ac.jpg

Link to comment
https://www.sau.com.au/forums/topic/439212-spare-time-31/#findComment-7202292
Share on other sites

i also got out my pwr radiator with inbuilt oil cooler, its farken expensive so naturally it did not fit lol, close but no cigar( will have to re-drill the upper mounts)
also dummy mounted the ic using the gtr mounts ( slightly modified)
they are not centered so will have to make something up and shift it left about 2 inches to center it
will also need additional bracing as its a big f**ker
icplusrad_zps666785f2.jpg

Link to comment
https://www.sau.com.au/forums/topic/439212-spare-time-31/#findComment-7202435
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...