Jump to content
SAU Community

Recommended Posts

G'day guys, i have finally spent enough money on the engine (for the moment) and am starting to look more into the cosmetic side of things. Living in brisbane and working on an island off gladstone for 28 days at a time leaves me with alot of time to do research and hunt for places but it is hard to pick a good one. Does anyone have a place that they would recommend in brisbane or close to there that does resprays and would be able to fix the scratches on the body kit?

Cheers Mitch

Link to comment
https://www.sau.com.au/forums/topic/439806-recommended-resprays/
Share on other sites

G'day guys, i have finally spent enough money on the engine (for the moment) and am starting to look more into the cosmetic side of things. Living in brisbane and working on an island off gladstone for 28 days at a time leaves me with alot of time to do research and hunt for places but it is hard to pick a good one. Does anyone have a place that they would recommend in brisbane or close to there that does resprays and would be able to fix the scratches on the body kit?

Cheers Mitch

Respraying a body kit can be done by pretty much anywhere if your paint is standard. Very easy job and should not cost much. Or are you looking at a complete respray?

have u considered plastidip?

i was thinking of doing that with the rims later down the track but not the entire car no

From experience not cameron's bodyworks unless you want to pay for it to be done again by someone else, so there's one less for you to look at

haha righto, cool, i havent heard of them but thanks for the warning mate!

Respraying a body kit can be done by pretty much anywhere if your paint is standard. Very easy job and should not cost much. Or are you looking at a complete respray?

theres a few small dents on the steel and the body kit is abit scratched abit here and there so im thinking a full going over and touching up of the whole car

I thought about the price of a re-spray.

And i thought about how many tools and how much paint i could buy for half that.

So DIY of course, and i get to keep the tools. (that includes an awesome compressor)

Body work can take a lot of hours if its done well.

So you have to think about the cost per hour vs what you earn per hour.

Youtube has a lot of good teachers for all the things you will need to do.

For me my car is big boys Lego, i spend as much time messing with it as i do driving it.

So i guess it also depends on how much you like doing that stuff, a paint job is a BIG job for DIY.

I thought about the price of a re-spray.

And i thought about how many tools and how much paint i could buy for half that.

So DIY of course, and i get to keep the tools. (that includes an awesome compressor)

Body work can take a lot of hours if its done well.

So you have to think about the cost per hour vs what you earn per hour.

Youtube has a lot of good teachers for all the things you will need to do.

For me my car is big boys Lego, i spend as much time messing with it as i do driving it.

So i guess it also depends on how much you like doing that stuff, a paint job is a BIG job for DIY.

ive got an aircompressor at home, 45L or something like that but i dont think that it would cut the mustard haha. i did contemplate doing it myself only things are that i dont have anywhere at home enclosed enough to do a good job without the car being coated in dirt. im the same with the boys toys thing too, alot of the gear that gets done to the car mainly the cosmetic stuff i do all myself. with me working away and only being back at a week at a time it would be ideal for me to drop it off to a shop and leave it with them for the 4 weeks that i am away giving them plenty of time to sort it out and then pick it up when i get back.

Edited by surfm8

Honestly i wouldnt recommend doing a respray yourself. It is a huge job and you really have to commit. I wouldn't expect a full respray to be more than 8k if you are going a standard colour. I think i was quoted around 10-12k from the most expensive painted in Canberra to do mine again and i have custom paint.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
×
×
  • Create New...