Jump to content
SAU Community

Help Me Setting Up Nismo R-Tune Ext Reservoir Coilovers

andreR34
 Share

Recommended Posts

andreR34 Explorer

andreR34

Posted
Posted

Hi Guys,

I just bought Nismo R-Tune coilovers with external reservoir which basically the same as the Ohlins. The spring rate are F: 9kg, R: 8kg.

I'm planning to use them as daily driving. do you know how to setup these for the street ?

They have 30 clicks adjustment for rebound ( top shocks knob ) and 20 clicks adjustment for compression (bottom reservoir knob )

what will be the optimal front and rear set-up rebound and compression setting for street use ?

what's the softest setting for rebound and compression ?

do you recommend changing spring rates for daily driving ? what are your recommendation ?

Please share your thoughts

Thank you very much

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

There's my thought: if you're going to use your car for daily driving, why not get the S-Tune suspension? You wouldn't have to worry about setting up the dampers too much either.

But, try running it around the middle and fiddle with the damper settings until it feels good to you. The spring rates are pretty stiff for the road, the R-Tune is mainly a track day suspension.

Piggaz Grand Master

Piggaz

Posted
Posted

Had the S and R tunes on my own car.

S tunes are fine for the street, not so much for the track.

R tunes are very uncomfortable and definitely not designed for out roads. Changing spring rates will only get you so far, it's the valving which you need to change.

As a comparison, I had made custom Bilstiens for my car with spring rates of 14 F and 9 R. Around town they ride just as soft as stock suspension, believe it or not. There is a lot more to it than just a cheap and easy spring change.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...