Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

stop gettin offtopic, but I had to go thru sex ed in high school too you know... oh and I did go thru puberty myself and all so that would be a strong influence lol

its NOT midnight purple II

it IS an aftermarket paintjob

i know this for a fact if you sit that car next to RH9 you will notice the difference ill try and post pics of both the cars so you can see how far off it is

I was going to be rude, but I just don't have the energy tonight sad2.gif

RH9 (Jason's car) is Midnight Purple II.

The R34 on Parramatta Rd, and the one posted by Funky is Midnight Purple III.

R34 GTRs had TWO Midnight Purple colours FROM FACTORY... Yes, that's right... Contrary to what you seem to be so sure of, it IS a factory colour.

Here are the paint codes for BNR34:

TV2 : Bayside Blue

QM1 : White

KR4 : Sonic Silver

KV2 : Athlete Silver

GV1 : Black Pearl

AR2 : Active Red

EV1 : Lightning Yellow

LV4 : Midnight Purple II

LX0 : Midnight Purple III

WV2 : Sparkling Silver

QX1 : White Pearl

EY0 : Sillica Breath

JW0 : Millennium Jade

that colour is AWESOME!

does it look like 'cameleon' (spelling) paint to anyone else?

its a 3 tone harlequin (or chameleon depending on which brand you prefer) paint by Dupont specially mixed up for Nissan Japan. The main colours are Dark Blue, Purple and Burnt Orange in that order of spectrum.

I tried to find a supplier in japan that could get me the paint from Nissan, but they said it costs way too much, and most Dupont dealers have the combination codes so they can mix up something similar anyways cheaper than Nissan can supply to them for. Then again, this is Japanese Dupont dealers and not the crummy aussie ones.

What's my colour name?

It's like a silver with purple pearl....  It's a GT-T

Look in your engine bay for your blue Nissan Build Plate, and look for a 3 letter code and match it up to the table I posted above...

That's the table for R34 GTR, which has a few more colour choices than the GT-t, but all the GT-t colours should be there I think...

its a 3 tone harlequin (or chameleon depending on which brand you prefer) paint by Dupont specially mixed up for Nissan Japan. The main colours are Dark Blue, Purple and Burnt Orange in that order of spectrum.

I tried to find a supplier in japan that could get me the paint from Nissan, but they said it costs way too much, and most Dupont dealers have the combination codes so they can mix up something similar anyways cheaper than Nissan can supply to them for. Then again, this is Japanese Dupont dealers and not the crummy aussie ones.

Why do you have to buy dupont?????Protech in airport west have these colours...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...