Jump to content
SAU Community

Recommended Posts

Yeah will find out. I think you should vent the BOV to atmo. There is atleast 1k RPM in response. and an extra 200kw

already is.

lololololztutututututututututututu.

I have a couple of Pure JDM HKS ones that vent to atmos that were loud as fk on my gtr.

Like these:

SDC13973.jpg

But srsly Plumb it back properly bruh

lol, there is nothing there to plumb it back too mate. at all. maybe if someone coughed up a gtr bov, i could get scotty to weld someting up.

I'm sure someone in vic will have a stock BOV floating around?

Those HKS ones are loud as f**k. Twas great.

I don't has Stock ones spare as i went back to stock to make motor run betterererer

It's possibly the cooler is too big. What about running like a 200sx cooler or stock r33 gts-t cooler? something smaller? That's a question for someone that really knows what they are talking about

Dump should make quite a bit of difference.

EVO 6-9 intercooler would be best :yes:

EVO 6-9 intercooler would be best :yes:

going by the size of them mick i dont think it would make that much difference!!!!!!!! but its something i can look into at a later date.

right i started pulling it down last night. turbo, cooler, dump and manifold off.

gotta check all the timing marks are in the right place and take the chain off. then cams out and head off. excited too see what state a 300km engine is in......

dump pipe is so obviously a restriction its mad. its f**king tiny and must be destroyed. cue scotty and a custom one.

or does anyone have one r33 gtr dump pipe aftermarket available?!

just a quick recap of parts,

custom front pipe 2.5 inch to cat, 2 inch to VAG diesel muffler built by scotty. thanks!

stock gtr 33 dump and turbo. thanks grant for supplying!

custom cheapo ebay knock off hks filter that bolts straight to the turbo. thanks ebay!

custom very short cooler piping. cheers scotty.

ford xr6t intercooler again scotty with some help from alvin

stagea/r34 370cc injectors. you guessed it, scotty!

r33 gtr fuel pump thanks greg!

custom made knive edge steampipe manifold thanks scotty

soon to be jdm plastic rocker cover, micra

arp studs, usa. actually from a ford escort....

ga15 throttle body and afm, my mate in NZ

sr20 oil filter re locator modified to fit cg13, with un regulated oil cooler.

nistune'd by dmd tuning on e85. thanks david

jun 4.2kg flywheel (10kg lighter) micra forum.

exedy heavy duty clutch. same

bc coilovers front, kyb shocks rear with tein springs not telling.

nismo rear sway bar, whiteline pan hard rod. micra forum for sway and me dad for xmas for the rod!

rear disc brake axle conversion. harveys wreckers in langwarrin. great blokes.

front n14sss brakes with hel braided lines, rda slotted and dimpled rotors and qfm a1rm pads. brakes from wreck, lines rotors and pads supplied by jason at garage 9. thanks!

super s front bumper. harveys langwarrin.

n14sss/gtir wheels wreck.

suziki swift ver3 recaro front seats, tony tran, thanks man.

n13 pulsar steering wheel. wreck.

i think thats about it!

thanks to dave as well for coming and being my eyes the night before roady when i couldnt f**king function any more.

if ive missed anyone, please chirp up its been that long and ive had that many parts from you all i cant remember!

one last thing, scotty is a mate, but 90% of the things he supplied and built where paid for. he is a buisness after all! the other ten percent was bourbon, jerky and foaming hand shandies.

Good list of parts mate. Whats the filter element like in your Pod filter? That could also be restricting you a little bit?

Get us the dyno chart reading when it next goes up!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...