Jump to content
SAU Community

1994 Toyota Soarer Jzz30

CLNSKY
 Share

Recommended Posts

CLNSKY Experienced

CLNSKY

Posted
Posted

have decided to put my car for sale. I have owned the car since 2009, and had another Soarer prior to this. The car is in excellent condition inside and out, and rarely driven but stays in the garage. When driven it sounds excellent and handles like it is on rails


I have logs of everything I have done to the car since I have bought it. There is a build thread on JDMST if you are interested.


The car has been tuned to 230rwkw, but has more potential as I have recently replaced the coilpacks, 440c injectors and fuel pump. It has the potential to make 250rwkw without a problem.


A recent compression test revealed 180 on all cylinders. Wet compression was 1: 215 2: 210 3: 215 4: 210 5: 210 6: 215


Body Respray in 202 Toyota black (same colour as stock) Fujin front lip, with late model front bar Autocouture side skirts Autocouture rear bar Origin roof spoiler Clear headlights Vertex clear sidemarkers Late model foglights Late model tailights LED turn signals, brake signals, interior lighting. All guards rolled


Engine/Mechanical R154 stock manual Stock airbox and panel filter modified with 6inch intake to area under headlight. FMIC sprayed black. Fits well and will not move in an accident. Eboost 2 Turbo timer Custom turbo back exhaust done by Hakan at Performance Exhaust Northmead, ending in a pair of Blitz Nur Spec mufflers. New Exedy HD clutch. New coil packs Bosch 040 fuel pump Supra 440c injectors Mines ECU


Suspension GAB coilovers rear JIC magic coilovers front New front LCA bushes (rubber, Vlamos). Superpro rear UCA bushes. Cusco front strut bar Torsen LSD LS400 4 Pot front brakes Supra 2 Pot rear brakes HEL SS brake lines


Wheels Will be sold with R32GTR Vspec 2 rims with Dunlop Direzza tyres. 80-90% tread. OR Work Meister 19 inch. New RE001 Front, 70% AD08 Rear


Interior Black interior Recaro SRZero front seats (pair) Floor mats Smaller Toyota steering wheel. Fire extinguisher JVC din stereo Audio - unsure on this but it has a Kicker Sub, tweeters etc and an amp.


Meisters


1479535_10151884509289527_261523735_n.jp



BBS dscf00282i.jpg



R32 GTR VspecII rims


277834_10150971794334527_1198746764_o.jp


Interior


417157_10150588081119527_586915125_n.jpg




408130_10150588081024527_1462494705_n.jp


I am in NO RUSH to sell. I will only reply to genuine expressions of interest. $14000 with MEISTERS (yes I know it's high, but you will not find another Soarer in this condition)


The car sits in the garage and does not get driven. Serviced every 6 months, driven or not.


PM me if you are interested or have any questions.



Thanks,

Link to comment
https://www.sau.com.au/forums/topic/442760-1994-toyota-soarer-jzz30/
Share on other sites
  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      It's been quite the ordeal but hey, at least you figured it out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...