Jump to content
SAU Community

Recommended Posts

You always will have some vacuum, how else would the car run?

How much do you need your brakes to work at idle?

The booster stores vacuum, so even if you somehow had no vacuum at idle your brakes would still work.

Well close to 500rwkw. I have tomei 270 10.25, but not sure if i should go 280 10.8? I wanna do things once and only once... Just worries about vacuum for brakes. Dnt wanna end up wit -3 or -4 for idle. After all its a weekender car...

The standard map sensor on the haltech comp is gonna be my limit! Lol otherwise its gonna be box and diff every couple of months!! Besides hks stroker is rated to 588kw so at the wheels would be about 470kw

Edited by DannyzGTR

Leave the duration alone. You'll go backwards!

NYTSKY made 550 on the same turbo with 256 and 264 on 25 psi ( IIRC )

Turn it up! No point having such a monster turbo and running it on fairy boost.

The standard map sensor on the haltech comp is gonna be me limit! Lol otherwise its gonna box and diff every couple of months!! Besides hks stroker is rated to 588kw so at the wheels would be about 470kw

Nice looking car but can't follow your logic. Do you want more power or not? A new map sensor will be cheaper than new cams and get your tuner to wind up the boost until you hit 500kw if that's your target.

  • Like 1

Map sounds cheap but haltech know how to screw ppl, harness to run it

Cost $200 and map sensor $140.

Ps. built cost so far 35k and thats me doing all mechanical work, trade prices on 90% of parts!, and some 2nd parts!

Edited by DannyzGTR

So you have a meh stroker kit in it

but want huge cams so you can rev a meh crank to 11ty

but wont buy a map sensor to run a couple more psi

Hmmm what will kill the engine quicker?

27 billion rpm or a bit more boost?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...