Jump to content
SAU Community

Recommended Posts

R34 GTT with R34 RB26

Probably should of started this thread before the freshen up!

Fresh respray in custom grey

Viva Garage R34 R-style Side Skirts and front bumper

Blits ADR Approved bonnet

Freshly rebuilt R34 RB26DETT
HKS Gt2530's
Custom Dumps and exhaust
N1 Oil Pump with Spool Billet Gears
Tomei Type B Poncams
Driftworks / Mocal Thermostatic Oil Cooler Kit
Nismo AFM's
ID1000 Injectors
FPR2000
Aftermarket Industries Surge Tank and Holley Dominator Pump Combo
Walbro E85 Intank Pump
Blitz GTR FMIC
Power FC (for now)
Jim Berry "Full Monty" Clutch
Nismo GT PRO LSD 1.5way diff centre installed less than 5000 km's ago
HEL Braided Brake Lines

HEL ABS Delete Kit

DBA Front Disc Rotors and QFM A1RM Pads
DBA Rear Disc Rotor and Bendix Ultimate brake pads
Apexi Type R Coilovers
Defi gauge cluster (oil temp, exhaust temp, water temp and boost)
Innovate Wideband Controller
Blitz 4 stage electronic boost controller

Cartel Drag Wing
20x9.5 / 20x10.5 R35 GTR Wheels

Makes 522hp on BP98, will have e85 figures soon - tuned by Trent @ Mercury Motorsport

post-50388-0-14926900-1400058286_thumb.jpg

post-50388-0-47559500-1400058297_thumb.jpg

post-50388-0-33473300-1400058308_thumb.jpg

post-50388-0-37464700-1400058321_thumb.jpg

post-50388-0-75460500-1400058332_thumb.jpg

post-50388-0-97445400-1400058346_thumb.jpg

E85 tune should see 600hp.

Got some 18x9/18x10 flow forms on it for drift/circuit use (rears in photo below)

350z gearbox is on my to-do list, dont ask my why I just think it needs another cog

And may go down the single turbo conversion some time soon

10154312_1482726268607135_49298526705939

Edited by The WOR57

Nice car man. Have you hit up any track events yet?

Where did you get the spoiler by the way?

Car did a powercruise when it shat an oil pump - hence it came off the road for a freshen up which became full respray etc also.

Has since done one drift event, has only been tuned a fortnight or so.

Wing available here: http://www.shop.cartel-aus.com/Drift-Drag-Wing-Drift-Drag-Wing.htm

how hard was it to get the R35 rims to fit up?

Needed 25mm spacer on front, front guards are not rolled even so they poke a tiny bit - rear guards are rolled but only running 245/30 tyre so theres plenty of room to prevent scrubbing.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...