Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

when are you expecting r33 rears.. i will probably grab one.

on another note, doesnt sound much like a group buy.. more like a business ad.

Please contact me about this.

Dave.

4-5 weeks...i can be contacted at [email protected] if you want to find me?

  • 2 weeks later...

sorry i havent been replying to pm's regularly guys...there just too many atm HOWEVER i ALWAYS check my email and will endovour to get through as many pms as possible

basically there are currenly sold, more will be in abt 3 weeks

i will post when they are avalible.

cheers

greg

  • 2 weeks later...
  • 4 weeks later...
Hey guys

Making/fitting rear braces for the r33 is not possible, due to its lack accessibility, UNLESS its GTR in which case it comes with a rear brace from the factory... :D  

sorry... :D

My R33 (series I) had a Skyline branded rear brace already fitted when I bought it in May 2004.

But it is an active LSD model - GTS25t.M/LSD. Perhaps this model had a rear brace fitted as standard????? Anyone know????????

Whatever, it doesn't have front brace, and would like one of these.

Greg, any R33 front braces left?

They are back!

I expect Delivery to commence in early Speptember.

Strut Braces for:

SR Silvia/180sx FRONT (NO CA FRONTS SEE BELOW)

CA/SR Silvia/180sx REAR

S14 f & r

S15 f & r

R32 f & r

R33 front

z32 Front

JA80 Supra Front

Flat price is $85 for one, $150 for two.

This includes delivery to you door using Australia Post.

The price has risen slightly from last time, unfortunately this is due to a material cost increase and totally beyond my control.

COD and pick up are not available.

Other braces are NOT available, if and/or when they are i will post, please refrain from asking me if i can get them for your moms mini/lancer/prado etc, i dont mean to be rude but i simply dont have the time to respond to these sorts of emails .

Direct deposit is the only form of payment that is quick easy and simple unless you are in melbourne and wish to pay cash. This still requires postage as they are coming down from queensland, and they will be shipped to your door.

Please feel free to post all other questions and i will get back to you ASAP.

I will send my bank details via email, please feel free to post any other questions.

They are $85 for one, or $150for two including delivery Australia Wide!

For pics see: http://domainsheaven.com/forum/posting.php...e=editpost&p=17

(you will have to sign up, but its quick, easy and free!)

cheers

[email protected]

=======================================================

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...