Jump to content
SAU Community

Recommended Posts

Bob you'll need to specify the model.

There's pre 91, post 91 and N1.

Ok....... I need both pre and post 91's for my ADM and V-Spec2.... N1 not so important.

I know the High beams are the same H3's and the Low beams are H3c and H1 respectively but I want to know the wattage.

Thanks,

Bob.

The 85W bulbs are std....... I had it checked out with Nissan yesterday.

I bought some "you-beaut" Phillips globes as the cars going back to Unigroup on Monday and I figured they can throw them in for me but..............

In the box of goodies I got from the previous owner there is a pair of H11 globes and a pair of HB3's..........

I'm hoping that it's just a coincidence (and error) that he gave them to me as I can't see anywhere our cars taking these globes.

A post "91 car should be H1's and H3's and these are for my V-Spec 2.

This is what I bought, I couldn't get The H1's in 85W bar Nissan and I wasn't going to pay $77.00 for a pair!

I could get 100W but it's risky putting more load on the wiring.

I got these 55W but with extra 60% coverage according to the box! How often do I use high beam....... Not often.

Hopefully they all fit.

Bob.

post-78207-0-25292700-1401522558_thumb.jpg

post-78207-0-74985700-1401522563_thumb.jpg

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Hmmm...... Good point....... My parts guy knows I have 2 cars but may well of quoted based on the ADM.

Maybe the later cars got this upgrade too?

I'll know more tomorrow after they hopefully fit what I will give them.

I'll let you know.

Bob.

I probably should have just looked in the owners manual instead of digging bulbs out of suspect headlight assemblies !!!

Well...... That's our answer well done........ I think. What does the 2 and 4 mean on the top two lines?

Thanks,

Bob.

My handbook is for all model Skylines and I think sedans had a combination headlight which used the H4, thus only 2-headlights.

My car has individual low beam lights and high beam lights, thus 4-headlights.

I can't read Jap, so I'm just guessing.

The next light below (with the H3 12v/55W) would be for the fog light.

But Bob your question is doing my head in.

Handbook says H1 on high beam.

To my knowledge R32 projectors use either a H1 or a H3C on low, but they all use a H3 on high??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...