Jump to content
SAU Community

Recommended Posts

Bob you'll need to specify the model.

There's pre 91, post 91 and N1.

Ok....... I need both pre and post 91's for my ADM and V-Spec2.... N1 not so important.

I know the High beams are the same H3's and the Low beams are H3c and H1 respectively but I want to know the wattage.

Thanks,

Bob.

The 85W bulbs are std....... I had it checked out with Nissan yesterday.

I bought some "you-beaut" Phillips globes as the cars going back to Unigroup on Monday and I figured they can throw them in for me but..............

In the box of goodies I got from the previous owner there is a pair of H11 globes and a pair of HB3's..........

I'm hoping that it's just a coincidence (and error) that he gave them to me as I can't see anywhere our cars taking these globes.

A post "91 car should be H1's and H3's and these are for my V-Spec 2.

This is what I bought, I couldn't get The H1's in 85W bar Nissan and I wasn't going to pay $77.00 for a pair!

I could get 100W but it's risky putting more load on the wiring.

I got these 55W but with extra 60% coverage according to the box! How often do I use high beam....... Not often.

Hopefully they all fit.

Bob.

post-78207-0-25292700-1401522558_thumb.jpg

post-78207-0-74985700-1401522563_thumb.jpg

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Hmmm...... Good point....... My parts guy knows I have 2 cars but may well of quoted based on the ADM.

Maybe the later cars got this upgrade too?

I'll know more tomorrow after they hopefully fit what I will give them.

I'll let you know.

Bob.

I probably should have just looked in the owners manual instead of digging bulbs out of suspect headlight assemblies !!!

Well...... That's our answer well done........ I think. What does the 2 and 4 mean on the top two lines?

Thanks,

Bob.

My handbook is for all model Skylines and I think sedans had a combination headlight which used the H4, thus only 2-headlights.

My car has individual low beam lights and high beam lights, thus 4-headlights.

I can't read Jap, so I'm just guessing.

The next light below (with the H3 12v/55W) would be for the fog light.

But Bob your question is doing my head in.

Handbook says H1 on high beam.

To my knowledge R32 projectors use either a H1 or a H3C on low, but they all use a H3 on high??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...