Jump to content
SAU Community

Recommended Posts

While rebuilding the S1 Dayz RS4, I measured the thickness of the core at 25mm. I compared it to the other RS4, the one that has the "gurgles", and was very surprised to see it was only 17mm.. Even the 25G is 25mm.

I now recall that when I was fitting the FFP I broke the top hose connection and bought a replacement radiator off the forum, never noticing the different thickness. Someone flogged me a bodgie rad. My BAD..Buyer beware. When the 25G got front shunted I used the core off the RS4 to get the rad fixed. Hence it being 25mm now. It runs cool as a cucumber.

Just maybe, the reason the 17mm Stag has the gurgles is because the rad is too thin and it boils when pushed?

Next thing is to get a Rad with a 25 plus core.

Link to comment
https://www.sau.com.au/forums/topic/444154-c34-radiator-core-thickness/
Share on other sites

  • 8 months later...

Not only an FMIC but also a tranny cooler. I had thought of putting in an oil cooler but I have a remote oil filter also and it would have been a PITA to fit. The alloy rad fixed all.

Edited by 66yostagea

S1 is quite thin (approx 15mm, same as R33 GTST IIRC)

An aftermarket koyo rad (standard construction, plastic top and bottom tanks) is thicker at about 25mm, but has fewer flutes than the stock rad, as the flutes are wider.

No idea which would flow better, could be a close call (fewer large flutes v's more smaller flutes) but surely additional thickness will improve cooling?

Y31 Cima rad is identical in width/height as the C34/R33 rad, but is double row, so a good upgrade for cheap if you can get one!

Edited by crazy86

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...