Jump to content
SAU Community

Rwd Auto Box Wtb

66yostagea
 Share

Recommended Posts

66yostagea Grand Master

66yostagea

Posted
Posted

I know most Stag owners will regard this as a retrograde step. But at my age auto is the best for my wife and me.

I am slowly rebuilding an RWD motor for the S1 Dayz.. The drive front shafts are out. I suppose I could use the 4WD box but

wonder what to do with the box front output. Can a cover be fitted to keep the crud out?

So I am looking at fitting an RWD auto box. Is this possible? What type will slot straight in..

So I wtb an RWD auto box Would prefer Brisvegas pick up.

Link to comment
https://www.sau.com.au/forums/topic/445245-rwd-auto-box-wtb/
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted

The motor going in is an RWD motor, so want an RWD box.

Yes I get that. But the car is 4wd right?

so you have a 4wd box which will defiintiely fit and work. It just has a hole that needs blocking.

Thats the easiest option.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Yes I get that. But the car is 4wd right?

so you have a 4wd box which will defiintiely fit and work. It just has a hole that needs blocking.

Thats the easiest option.

Strictly it doesn't even need blocking - it has a seal and anything that does somehow get past the seal is just going into the now redundant transfer case.

And the auto box is a heavy item to lug around - save yourself the bother!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...