Jump to content
SAU Community

Recommended Posts

All items are no longer needed or incorrect for my car see more details below. All prices negotiable, need the space in the garage again. If they don’t sell they will be in the bin, so make an offer. Ive guessed the prices so some may be way off.

All items are located in NSW, Sydney. Near Liverpool. Will post, however postage will be extra and if a courier is needed the buyer is to organize. Wont send them until the cash is in my account, and will be still on the market until cash is in my account.

Can get in contact with me by calling 0421 845 346 or PM

20140705_150715.jpg

20140705_150724.jpg

20140705_150733.jpg

Blitz return flow intercooler, has been used for street work before I bought the car. In good condition.

600 x 270 x 70 core and 740mm from end to end. 2.5 inch outlets

$200

20140705_150830.jpg

R32 GTS-T rear seat, car has 118 000kms on it. The seat looks near unused! Sun fading on the top, mark on the top right too might clean out.

$50

20140705_151237.jpg

20140705_151306.jpg

20140705_151252.jpg

GTR drivers seat, think its an R32 as it has come out of my R32. Rip in bolster and rub from the seat belt. Including seat base however you will need to re-use your seat belt buckle.

$150

20140705_151705.jpg

20140705_151710.jpg

R32 carpet. In good condition as you can see the pics, small amount of wear but not much. Has been cut to allow installation without removing the console, cant tell when installed

$100

20140705_151856.jpg

20140530_144220.jpg

20140530_144214.jpg

Boot lining, including carpet, sides and rear. In good condition however the carpet has seen better days

$80 for the lot

20140705_152248.jpg

Spare wheel, spare wheel cover and jack. Will sell separate

$100 for the lot

20140705_152324.jpg

R32 Kick panels, drivers and passenger side

$20 each

20140705_152344.jpg

R32 Centre console, good condition, some marks however. As before car has 118 00kms

$80

20140705_152554.jpg

RB25 DET standard manifold, unsure of KMS as the engine change on my car wasn’t done by me. Includes what is seen in the picture, might be missing items

$20

20140705_152807.jpg

R32 rear seat belts, includes what can be seen in the pic. I believe they are complete including bolts

$100

20140705_152918.jpg

Standard RB25 DET oil cooler

$40

20140705_152935.jpg

Remote filter adapter, no stud just what you can see

$40

20140705_153008.jpg

20140705_153020.jpg

Fuel rail for RB25DET, to suit top flow injectors. Includes mounting kit, may be missing a washer or two. Brand new never fitted, has some small shipping and garage living marks

$50

20140705_153128.jpg

JVC head unit, not sure what brand. Can get more info if someone is really interested. Cant guarantee it works as when I picked up the car it wasn’t (believe its just a fuse on the car that stopped it working but cant confirm that. If you know how to test it before you take it away no problems at all)

$50

20140705_153155.jpg

20140705_153209.jpg

90mm throttle body for RB25 DET, brand new never fitted. Too big for what I need.

$80

20140705_153235.jpg

Rear parcel shelf for R32 GTS-T. Wood backing isn’t broken, could do with a clean. Good condition however

$40

20140705_153241.jpg

Rear interior cards, good condition however one is missing the fabric

$40 for both

20140705_153250.jpg

Rear C pillar trim and heater separator. The pillar trims are broken in the corners but good enough for a road worthy!

$20 for heater separator and $20 for trim

20140705_153358.jpg

R32 GTS-T hicas. Was unplumbed when I removed it so unsure if it works. Comes with two tie rods. Good enough condition

$50

20140705_153509.jpg

Clear indicators, GTR or GTS-T not sure they were in the glovebox! Also not sure if they work as they wernt connected to the car.

$50

If you have a steering wheel then I'm keen for a PM :)

Will grab the active speaker covers and parcel shelf. PM incoming :)

Edited by Sinista32

Think the last lights are not actually indicators, believe them to be licence plate lights.

Parcel shelf sold, well the speaker covers anyway. The buyer doesnt need the parcel shelf so if anyone if after the shelf minus the speaker covers let me know. (This was cleared with the buyer as it will be cheaper on freight!!) If not, in the bin it will go!

Interested in gearshift surround if all tabs are in good condition. PM if it's for sale.

In case you don't know what I'm talking about; I've attached a pic for reference.

post-28600-1259841736.jpg

Intercooler sold.

Parcel shelf and speaker covers back on the market. When i pulled the speaker covers off to shop as per the buyers request, two plastic tabs broke so he no longer wanted them. Other than that, no dramas with them.

Still negotiable on all the gear, get in before it goes in the bin.

Thanks mate, nice and easy way to do business.

All right, buy my stuff!!

Rear seat

$20

Carpet

$75

Boot lining

$50

Spare wheel items

$50

Centre console

$50

Manifold

$Free

Seat belts

$50

Standard oil cooler

$20

Fuel rail

$50 still

Throttle body

$50

Door cards

$Free

Buy my stuff!

I realise the manifold is free and you just wanna get rid of it with the minimum of fuss but are you willing to post it and if so how much to NSW 2539?

already have a guy thats keen on the manifold if i want to post it but still free to pick up!!

its the intake manifold

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...