Jump to content
SAU Community

Recommended Posts

R33 gtr rb26 engine, head has been serviced new headgasket, arp studs, new valve stem seals, n1 oil pump, tomei oil restrictor, near new water pump and many more things.
Comes with r33 gtr turbos etc
Intake manifold + throttle bodies

Comp tested 160 1,2,3,4 157 5,6

-4000

Garrett 2860r -7 turbos great condition fully rebuilt 2500kms ago -1300

R32/33 nistune ecu, has tune just for exhaust intake and boost increase -450

R32 gtr seats pretty good condition -550
R32 gtr diff -500
R32 gtr rear wing -100
R32 front and rear strut braces -150
R32 gtr tailshaft -100
R32 gtr exhaust 3.5 to 5 inch tip

r32/33 gtr after market downpipe -100

r32 apexi duel bovs -100

r32 gtr intercooler and piping -200

Rb26 r33 gtr gearbox, no noises or crunches perfect working order -900
Rb26 camtech cams used for start up only! Unknown spec but good for power, can drop in with stock valve springs -300
Rb26 apexi air intake + filters -100

Will upload pics on request

message me or text me on 0481360765 for more info

Edited by nickgtr32
Link to comment
https://www.sau.com.au/forums/topic/445502-rb26-engine-and-r32-gtrrb26-parts/
Share on other sites

Rear sway bar sold

Also have full r32 gtr brake set up for sale

4 piston fronts

2 piston rear

New seals

New discs and new genuine brembo race pads. Sprayed in black.

-$650

post-134644-1405944664586_thumb.jpg

N1 oil pump suit rb26 -$150

post-134644-14059445991667_thumb.jpgpost-134644-14059446092293_thumb.jpg

R32 gtr fibreglass headlight intake -$50

post-134644-14059445679537_thumb.jpg

R32/r33 gtr engine mounts near new -$75

post-134644-14059445497729_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...