Jump to content
SAU Community

Recommended Posts

Hey guys

Since some weeks I got this metallic sound from the rear of my car. At first it only appeared on the left, meanwhile on both sides.

It appears when I start moving the car, forward and reverse. Also when changing into 2nd and start accelerating.

It does NOT appear in every gear or always at the same "time". It sounds like 2 screwdrivers hit against each other.

Also you can not "make" that sound with "shaking" the car for example, so theres nothing haning around, nothing lose or not in place

and so on. A friend of mine is mechanic but we could only check without a lft but he couldnt find anything. Not the wheels, nor the suspension, not the exhaust, not the shieldings bla bla bla

I srsly got no clue what to do, and since a week, this guy has the same problem. Actually it´s not a real problem, at least so far. But everytime I stop and keep moving again, there´s that annoying sound and ofc that´s not how the car should be so I rly wanna fix that.

Sry for bad english, and sry for not being able to explain it better ^^

Here are two short vids, in which you can hear that sound. Sry for bad quality, cellphone sucks :) When you hear it, you´ll straight know what I am talking about.

Thanks a lot

http://www.dailymotion.com/video/k6mFvU0Vq7W3yw8kBlr

http://www.dailymotion.com/video/k1Am8JdGgI3N9O8flgQ

Link to comment
https://www.sau.com.au/forums/topic/445531-33-gtst-s2-metallic-noise/
Share on other sites

I jacked the car up and tried to shake and turn the wheels in every possible direction. Should I hear it then too? Cause there was nothing. But I´ll have a look again.

if there play in the wheel when u tried? u might not hear it unless the wheel is under load being driven

Nah I´d say nothing. I turned and shook em in every possible way. Like said before, if you would hear it while checking, you´d also hear it while the whole is getting kinda rumbled by driving over a curb for example, I guess. But that doesn´t happen

Somebody meant while driving by might be something to do with the "struts" ( if I got the correct Translation ). I can´t see how this could be oO If, it would be more centre of the car, not obviously down and rear, correct?

A stainless exhaust can make a similar noise when tapped, on take off the exhaust will tend to move/vibrate more

also if there was some loose fragments of broken cat converter, they could be tapping inside the pipes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...