Jump to content
SAU Community

Power Loss On Downshifts, Bouncing Idle And Slight Hesitation At Specific Rev Point -R34Gtt


Recommended Posts

Sorry my bad. I assumed that going a 3L you would upgrade the supporting mods, water and oil pump, timing belt, clutch and at least a dyno tune. Obviously not the case, I apologise.

You can't do it without a timing belt. Water pumps are cheap as. The rb30 oil pump is fine. Shim the relief valve for free.

And I tuned it on the dyno.

Widebands are the best.

I also thought my car was running rich.

Bought wideband.

Observed AFR.

Changed fuel maps to suit.

Car running correctly.

See also:

Got tune. Cold start was terrible. Idle was terrible (17:1).

Made 30 seconds of changes.

Car running correctly.

See also:

Car tuned on E85. Corrections for 98 not entirely right (known).

Get E58 or something in tank after tank swap.

Made 15 seconds of changes in correction map.

Car running correctly.

See also:

Changed injectors from 1000cc to 1400cc.

Car not running correctly.

Made 2 minutes of changes to fuel map.

Car running correctly.

GET A WIDEBAND

  • Like 2

Doing a RB25/30 conversion for less then $3k can be done IF you can do all of the work yourself and all good and well these guys say you can cause i did it is not a fair statement, you couldn't take you car to someone ( and not a mate ) and get it done for that, no way in hell

It also come to what supporting mods you do and to what level and how properly you do the conversion as we all know there are cheap way to do some stuff which isn't exactly the best way of doing it

So the real question would be can Ron do it for less then $3k done and dusted ?

  • Like 2

Again with the wide band, if tuned properly you shouldn't need one, nice to have but not needed cause really you can only do so much on the street before it should be put on a dyno and tuned properly

^^ This really clever fellow here knows me more than I know myself !!

Yes.

It's based on many things you have posted.

For example.

You specified how exactly you were going to block up your bov return. And did it weirdly anyway.

Someone who knows what they are doing just does stuff.

I do really hope you can get the car sorted out.

22 pages on AFM vs. BOV lol

I reckon, sell Power FC, BOV, AFM - buy Adaptronics, block up BOV port/return dose & bake tyres all day

  • Like 1

So in in Rons case it would go

Nistune, sell

Power fc sell

Adaptronic

???

Profit?

Edited by Ben C34

flutters is the shit man... you won't look back.. and no more reversion, no more stalling crap, no more dirty AFM, etc.

rip skids & be happy

  • Like 1

Again with the wide band, if tuned properly you shouldn't need one, nice to have but not needed cause really you can only do so much on the street before it should be put on a dyno and tuned properly

True enough for anything over 100kmh with a power run. The 97% of the driving you use a street car for however can be done with a wideband and some tinkering. The power runs is what the dyno is for but that is really only a small fraction of the time (money!) it takes for a tuner to tune the car, but I agree - it's no dyno replacement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...