Jump to content
SAU Community

Recommended Posts

I'm sold on the quaife front diff on a BNR32.. Right now I'm driving a OEM rear diff which is , most likely, 25 yr old! I have a ATS 1.5 way LSD lying around ( I put it for sale but no one bite the bullet yet..). Should I install this diff or sell it and buy a quaife in the rear OR just run the oem one ?

thanks!

I'M afraid the cost of rebuilt will be close to the cost of the Quaife ( seems like tranny shop are are in my area so they charge a lot knowing they have the ''monopole'' no shit.. its like 1000$ to rebuilt with the 300$ kit..)

im not sure where your located cobrAA but I have found myself in nearly the same situation..

I currently have a quaife front diff and a standard rear diff which im sure is not doing as a good a job as it could.

I spoke to Award at seven hills and they will re-shim the standard diff to make it tighter for 400ish dollars from what I can remember them telling me.. you have to pull the diff out yourself though.

In saying that a quaife rear would be the way to go based off how good the fronts are

Yeah so unless, I find a great deal on a quaife rear diff, i will buy the front and put the used ATS 1.5 there . thanks

Few people use the Quaife rear - most use the Nismo or recond stocker (or can you get Kaaz at a good price?)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...