Jump to content
SAU Community

Recommended Posts

Hey guys
So I finally got my car back after a whole year of waiting for the bumper to be fixed at the mechanic (terrible place). Before it entered the shop it had a fresh coat of paint on the whole car (about 1 month).

The other day I washed the car using just a hose, bucket and meguiars car wash. It wasn't overly hot and was washed in the shade. When I finished the car had this weird stuff scattered across the bonnet. I freaked out a little so thinking it was maybe the product I rewashed with the amourall brand product. It still didn't go away, so I thought maybe from being sitting around in a shop for so long something has stuck to the paint. So I got out the claybar and hit up a small section. No dice :(

Anyone got a clue or seen a similliar thing like this before? Any help would be much appreciated.

post-65084-0-43345600-1409024300_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/447280-weird-substance-on-paint/
Share on other sites

Looks like water spots/hard water etching. Wont come off with normal car wash or clay, you will need something more abrasive like a good quality polish. Keep the paint waxed and always dry the paint after a wash to prevent the marks from coming back

maybe a few more clearer pics. What are the other flat surfaces like (roof/boot)?

hopefully a good polish will resolve this what ever has caused it.

Do you know where they kept it (outside or in the corner of the shop)

hopefully not petroleum type products/fumes gathering on the freshish clear coat.

but yes it does look like water left on the vehicle drying up in the sun.

I went out and got some polish and some wax then went to town. Had great success in removing the stains from the car. Believe it was water spots/marks as stated. Gave the mob a call in regards to where it was kept. In the workshop for pretty much the whole time close to everything else that was going on in there.

Thank you for the good advice and help guys.

post-65084-0-66966900-1409120202_thumb.jpg

post-65084-0-03618900-1409120323_thumb.jpg

  • 4 weeks later...

my car came back from a workshop in Parramatta with what I think was fine metal dust over it. could feel it when I ran the back of my hand along the panel. I do recall peoples rotors getting machined right near the hoist etc.

couple of washes was enough to get it off as I had a good sealant applied over the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...