Jump to content
SAU Community

Recommended Posts

Hey guys, just wondering if its possible to unplug the o2 sensors without causing damage to find out whether car runs fine without them in use to find out whether they are the cause of a surging problem while cruising on flat road at 100-110 km/h and slightly rough idle for 30-60 seconds before coming good. Dont want to go replacing them if theres a way to diagnose whether its them playing up or not first.

Running factory ecu by the way

Link to comment
https://www.sau.com.au/forums/topic/448749-unplugging-o2-sensors-on-r33gtr/
Share on other sites

Thanks guys. Changing spark plugs this afternoon so if that doesn't solve the hesitation/surging problem I'll try unplugging the o2 sensors and take it for a run to eliminate them or get confirmation i need a new set if it runs fine without them in use. Otherwise next step will be afm's.

Another question... If timing was changed slightly to suit power fc and then factory ecu was put back in, could that have anything to do with it? I've been told it shouldn't but Im not so sure

Well there you go. Youd think the place who tuned the power fc would have suggested that after i rang them when it started playing up asking if that could be the issue or if it needed to be done but said no it should be fine :-/ better find someone with a timing light then !

Changed spark plugs first with iridiums and started fine and idled fine while cold. I let it idle till it was warm as it was getting to nearly 2/3 on the temp gauge it started to idle rough like it was last time I drove it. Also changed the fuel filter and hasn't it don't its job since it was last changed. The black shit that was coming out of it was unreal so good thing I decided to change it anyway. After that the idle was still rough so figured i'de try unplugging the o2 sensors one at a time. unplugged rear one first and waited 10 seconds and no change. unplugged the front one waited about 5 seconds and low and behold the idle corrected itself and was purring like a kitten again, plugged it back in and after about 5 seconds.... idling rough.

Now I haven't yet been able to take it for a drive on the open road to see if the surging has gone away with the o2 sensor unplugged at between 100-110km/h where it was playing up before but fingers crossed once I put new o2 sensor in, it'll solve that issue too as it started at the same time the rougher idle did.

Thanks for everyones help and suggestions

AFAIK, the ECU ignores the O2 sensor(s) at idle and on a cold engine, so I am perplexed that unplugguing either of the sensors made any difference.

You may well have fouled the plugs by letting the engine simply idle to warm up. Engine runs rich when cold, best to drive it to warm up the engine faster. The fouled plugs, particularly if they are Iridiums, could well be a contributor to your idling problems.

The surging may well be the ATTESSA complaining about worn rear tyres.

Well it definitely did make a difference so I recommend others try the same if the same symptoms ever occur. I may try to get a video tomorrow to show the difference.

As for the plugs, if you read above, we actually only put the new plugs in today and the ones that we took out weren't fouled anyway but I just put the new ones in since I paid for the iridiums.

Never knew the attessa system complained about rear tyres lol. Im pretty sure there is still plenty of tread, it happened when just cruising on a flat, straight road at 100-110km/h at +/- 3000rpm so I doubt there would be any traction loss. Will take it for a drive tomorrow to see if it still does it.

AFAIK, the ECU ignores the O2 sensor(s) at idle and on a cold engine, so I am perplexed that unplugguing either of the sensors made any difference.

You may well have fouled the plugs by letting the engine simply idle to warm up. Engine runs rich when cold, best to drive it to warm up the engine faster. The fouled plugs, particularly if they are Iridiums, could well be a contributor to your idling problems.

The surging may well be the ATTESSA complaining about worn rear tyres.

the factory narrowband o2 sensors are used for idle and cruise conditions (light load) no factory tune car i've ever seen will foul plugs just from letting it idle to warm up. you are talking about water temp fuel correction....the ecu will input more fuel when the engine is cold.

Ok so just went for a good drive to sit on 100/110km/h for a fair while and low and behold, it drove better and smoother than its ever driven! No hesitation, surging at all and actually feels like it has more power and better acceleration which may have something to do with the filthy fuel filter we replaced lol.

  • Like 1

I had the same problem. It does affect the idle and definitely affects low rev cruise quality and mostly acceleration. By acceleration I mean backing off or cruise then move the accelerator and there is a flat spot or hesitation. Accel-enrichment does not help. Disconnected the O2 and drives just like a factory car. I have since changed all cells at light load and cruise to 14:1 AFR and run without a O2 sensor. It is better on fuel consumption at 420-430k to a tank and drives beautifully.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • hello! does anyone have a schematic that shows how to test the blower motor resistor for the vac system? i believe the part# is 27761-15U00. I think the resistor is toast, but would like to be able to test it somehow before i embark on the journey to find a new one. cheers! 27761-15U00
    • I don't know the answer to this, but did you have a look at the parts diagrams on amayama.com and see what they list around it for your car? As an example this should be it on my car. That's how I would check for required clips and things like that. But, I take no responsibility for you ending up with a box full of random OEM hoses, washers and clips after going down that path a few times. This definitely has never happened to me  
    • Most driving should* be done on one side of single lane divided roads. In the RHD world, you drive on the left side of the dividing line and the road is probably cambered equally on both sides. So your side of the road slopes away to the left. The same is true for the LHD world, just everything swapped to the other side and opposite slope. With a perfectly neutral, straight ahead wheel alignment designed to drive straight on a perfectly flat surface (or at least one that is level on the left-right axis, even if it has some slope in the fore-aft axis) you will not be able to drive on a cambered road without the car wanting to drift down the camber. You will need to add steering input in the opposite direction all the time. This is annoying. The solution has always been to set the camber and/or the caster to produce a continuous turning force in the opposite direction of the camber. The car will drive straight on the kind of camber for which it was set up, presumably as described in the top paragraph. But.... when the car is set up this way, as soon as you get into a lane, usually on a multi-lane surface road or highway, where the camber is not as presumed during setup, the car will usually pull to one side. In the RHD world, if you are in the fast lane on a big divided road, you are probably on the opposite camber compared to what the car was set up for (ie, sloping down to the right) and the combination of the setup and that camber will make the car want to go right pretty hard. Even a perfectly flat lane will tend to want to go right. There's no getting around it. Civil engineers who know their stuff (which is not an assumption that can always be made) will attempt to keep the variation in camber across a multi-lane road as small as possible, and if they can will attempt to make the fast lane as close to flat, or even cambered in the same direction as all the other lanes. This takes a lot of planning for drainage, control of levels, ability to deal with the elevation changes that occur at road junctions, etc etc. So it's not trivial to get it right. When they do make it work, then the annoyance is reduced, along with tyre wear, fuel consumption, etc. In theory, the civil engineers are supposed to worry about those aspects of road design also. * This used to be true, but now with very large highway systems, even just multi-lane surface roads running everywhere, it is less true now than it was, but the old assumption is the basis for describing the phenomenon, so let's just run with it for the moment.
    • I think the consensus was that's normal. Sloped road surfaces or something? I remember @silviaz went through this before. It might be one of those things you never notice until you pay attention to it.
    • Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
×
×
  • Create New...