Jump to content
SAU Community

C34 S1 Rear Diff Filler

roboat

By roboat,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Ben C34 Grand Master

Ben C34

Posted
Posted

I got to mine with a 3inch exhaust basically in the way just using my 1/2 inch ratchet straight into the plug ( or a short extention can't remember)

Finding it is harder than undoing it!

roboat Apprentice

roboat

Posted
  • Author
Posted

Ah well the car is going onto stands soon/this afternoon. Going to change the oil in my transfer case (hasn't been done since I've owned it) and maybe have a stab at flushing my gearbox. I bought some chef synthetic atf from supercheap a while ago to do the job (says it's matic d compliant/compatible).

roboat Apprentice

roboat

Posted
  • Author
Posted

I ended up flagging the rear diff and serviced my transfer case instead (did it with the car on the ground reaching under).

Car's too much effort to get off the ground, doesn't go up ramps I need to drive onto blocks of wood to get a jack under it and when I jack up one end and put it on stands I can't fit the jack under the other end lol. Might leave that one to the professionals.

Duncan Grand Master

Duncan

Posted
Posted

fkin A!

its a difficult job on the floor

plug often super tight

may need to remove cat back to get at it with enough leverage

and then you need to refill the damn thing from below, and fluid doesn't like travelling uphill.

dead easy on a hoist with the right tools

zoomzoom Mentor

zoomzoom

Posted
Posted

Hmm I didn't realise it was that much hassle. Ive done them quite a few times, and done it when I have the car up on 4 stands.

As I mentioned, a few flex joints helps to do the twisting outside the wheel well. Another pair of hands helps too! It's tricky keeping a floppy pole in a hole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...