Jump to content
SAU Community

Recommended Posts

Test Round results.

10404346_10153674610279386_5220120132117

What a great start to the season!!! only .023 in it at the line! Sorry it took a while to get these posted (me still learning iRacing leagues :P) Points have been adjusted to account for the test round on the iRacing league too. Will also make sure the both Mazdas are available for next race. So bugs are ironed out for next round, see you there! :)

  • 2 weeks later...

Tony, I just purchased iRacing and a wheel and interested in getting involved in this.

Found the league on iRacing. Should I just apply to join it?

Thats it, just apply and I'll add you when I'm on iRacing next (which is pretty much daily). See you on track :)

Thanks all for that race. Bit unusual the session disappeared for 10 mins but came back online.

Looks like I have some work to do to get even close to Tony and Sam! :yes:

Edited by Syphon

Was some good fun racing tonight had by all I hope. Here are the results and championship standings (adjusted points are from the test round). See you all next month at Lime Rock Park :)

1412453_10153733224074386_25590127833508

10959562_10153733223959386_9161554374794

  • 4 weeks later...

What a great night of racing!!! Here are tonight results as well as championship standings. Congrats as well to Sam on first place!!! Thanks everyone for racing and see you all next month :)

Results -

11046743_10153803665304386_4800704056253

Standings -

11043074_10153803665269386_5440469880670

was a good race. managed to make it to the end for the first time.

changing FOV really helped Tony, thanks for the tip. certainly need to practice more than one a month though :P

also it seems once you register for the race, you cant change car choice.




  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...