Jump to content
SAU Community

Recommended Posts

Hey guys,

I have currently got an R32 GT-R on the way from Japan and I received photos of it sitting at the port.

One thing that worried me is that the car appears to have very little fuel in it. Pictured below:

2ikbd3c.jpg

I'm just wondering, if cars are this low on fuel do they actually fill them up enough to continue driving them or do they just decide to let it run out and then move it with a forklift? Really worried about the sills and rails being damaged as I have heard that they arent that careful when it comes to those kind of things :(

Thanks guys.

  • Like 1

I know when I imported my boat from America, it had about 150 ltrs of fuel (half tank) customs did not like that and almost got a fine, got let off because it was my 1st import.

Because it's only needs a small amount, just to drive off n on and to yard max 4 to 5 km depending on location.....

But that'was my boat hope it helps.

Never imported a car, I hope I will in a few years.

Let us know how your experience went.

Edited by pol1on1

Personally, I'd expect it to be shipped with minimal fuel.

I seriously hope they don't use a forklift at either end like they used to back when.

I'm sure during your search locally (Aus) you would not have seen many without marks on the sills or rails.

Speak with your importer.

Damn it looks so clean. Congrats.

Edited by Sinista32
My r34's low fuel light was on after the auction & before it was driven on the boat .And it was still on when i picked it up from compliance 10 weeks later.post-93096-0-64185700-1345286175_thumb.jpg

My r34's low fuel light was on after the auction & before it was driven on the boat .And it was still on when i picked it up from compliance 10 weeks later.

Compliance workshop might have put some in some in. I have jusr heard that they don't do that at the port.

Just picked up a V36. Compliance put in 10L in, enough for me to drive to a fuel station and put in a full tank.

Picked up 2 Evo's last year. Both did not have any put in but still had fuel light on and I had to limp 2-3km to fill up.

I think that's how it normally is?

Not so much worried about compliance. It's more when it's at the port. I have heard they use forklifts to move them around.

Yes forklifts smash the chassis rail like pancakes , then car is worthless , i also had seats , steering wheels , gear knobs and floor mats all swapped over for hacked up ones during storage/shipping .

Edited by NISSAN GTR

Yes forklifts smash the chassis rail like pancakes , then car is worthless , i also had seats , steering wheels , gear knobs and floor mats all swapped over for hacked up ones during storage/shipping .

Or you could get the rails repaired.

My had something sharp used to take the badges @port in Aust, metal valve caps removed, rear boot clips taken. But that was in 2004. I'm sure the wharfies are much different now.......

Mine was imported late last year with zero fuel but the car only did 4km between the pre-purchase inspection and me picking it up from compliance. No damage to rails or anything but i did lose the contents of the glovebox somewhere along the line!

From my experience with equipment found at wharf facilities, their forks would do no damage to chassis rails.

A fork that can hump a 20t container is big gear with massive tynes that offer a huge area to spread the load, far greater than say, a tyre changing shop's air operated jacking equipment.

But once the car is shipped off to a road transport company, the size of the fork drops dramatically and these are the machines that might damage rails. (especially if the rails were suspect to start with)

Car haulage companies aren't keen on cars like Skylines which don't have the front bar clearance to clamber up their ramps so they often get forked onto the single vehicle spot above the cab.

You can be lucky, your car may still have the wedges in the front coils.

These raise the car's front eliminating problems for the drivers shuffling vehicles to/from the ship.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...