Jump to content
SAU Community

How Are Cars Treated When Shipping Between Japan And Australia?

MP_R33
 Share

Recommended Posts

MP_R33 Mentor

MP_R33

Posted
Posted

Hey guys,

I have currently got an R32 GT-R on the way from Japan and I received photos of it sitting at the port.

One thing that worried me is that the car appears to have very little fuel in it. Pictured below:

2ikbd3c.jpg

I'm just wondering, if cars are this low on fuel do they actually fill them up enough to continue driving them or do they just decide to let it run out and then move it with a forklift? Really worried about the sills and rails being damaged as I have heard that they arent that careful when it comes to those kind of things :(

Thanks guys.

  • Like 1
  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

japmuscle
japmuscle

I've worked at the wharf on and off for 10 years, Webb Dock - Port Melbourne. I only ever drove cars, I had nothing to do with containers other than occasional chain lashing. Cars come in with the abs

GH05T
GH05T

could be worse

jiffo
jiffo

From my experience with equipment found at wharf facilities, their forks would do no damage to chassis rails. A fork that can hump a 20t container is big gear with massive tynes that offer a huge are

pol1on1 Mentor

pol1on1

Posted
Posted (edited)

I know when I imported my boat from America, it had about 150 ltrs of fuel (half tank) customs did not like that and almost got a fine, got let off because it was my 1st import.

Because it's only needs a small amount, just to drive off n on and to yard max 4 to 5 km depending on location.....

But that'was my boat hope it helps.

Never imported a car, I hope I will in a few years.

Let us know how your experience went.

Edited by pol1on1
Sinista32 Grand Master

Sinista32

Posted
Posted (edited)

Personally, I'd expect it to be shipped with minimal fuel.

I seriously hope they don't use a forklift at either end like they used to back when.

I'm sure during your search locally (Aus) you would not have seen many without marks on the sills or rails.

Speak with your importer.

Damn it looks so clean. Congrats.

Edited by Sinista32
I gotta R34gtr v-spec Collaborator

I gotta R34gtr v-spec

Posted
Posted
My r34's low fuel light was on after the auction & before it was driven on the boat .And it was still on when i picked it up from compliance 10 weeks later.post-93096-0-64185700-1345286175_thumb.jpg
MP_R33 Mentor

MP_R33

Posted
  • Author
Posted

My r34's low fuel light was on after the auction & before it was driven on the boat .And it was still on when i picked it up from compliance 10 weeks later.

Compliance workshop might have put some in some in. I have jusr heard that they don't do that at the port.

ShawnG Apprentice

ShawnG

Posted
Posted

Just picked up a V36. Compliance put in 10L in, enough for me to drive to a fuel station and put in a full tank.

Picked up 2 Evo's last year. Both did not have any put in but still had fuel light on and I had to limp 2-3km to fill up.

I think that's how it normally is?

NISSAN GTR Veteran

NISSAN GTR

Posted
Posted (edited)

Not so much worried about compliance. It's more when it's at the port. I have heard they use forklifts to move them around.

Yes forklifts smash the chassis rail like pancakes , then car is worthless , i also had seats , steering wheels , gear knobs and floor mats all swapped over for hacked up ones during storage/shipping .

Edited by NISSAN GTR
RBN1 Mentor

RBN1

Posted
Posted

Yes forklifts smash the chassis rail like pancakes , then car is worthless , i also had seats , steering wheels , gear knobs and floor mats all swapped over for hacked up ones during storage/shipping .

Or you could get the rails repaired.

My had something sharp used to take the badges @port in Aust, metal valve caps removed, rear boot clips taken. But that was in 2004. I'm sure the wharfies are much different now.......

nashy311 Apprentice

nashy311

Posted
Posted

Mine was imported late last year with zero fuel but the car only did 4km between the pre-purchase inspection and me picking it up from compliance. No damage to rails or anything but i did lose the contents of the glovebox somewhere along the line!

jiffo Mentor

jiffo

Posted
Posted

From my experience with equipment found at wharf facilities, their forks would do no damage to chassis rails.

A fork that can hump a 20t container is big gear with massive tynes that offer a huge area to spread the load, far greater than say, a tyre changing shop's air operated jacking equipment.

But once the car is shipped off to a road transport company, the size of the fork drops dramatically and these are the machines that might damage rails. (especially if the rails were suspect to start with)

Car haulage companies aren't keen on cars like Skylines which don't have the front bar clearance to clamber up their ramps so they often get forked onto the single vehicle spot above the cab.

You can be lucky, your car may still have the wedges in the front coils.

These raise the car's front eliminating problems for the drivers shuffling vehicles to/from the ship.

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...