Jump to content
SAU Community

Recommended Posts

Terry I've got photos somewhere of old mates transporting brand new FJ Holdens to the N.T.

They'd put 2-carpenter's planks through the opened windows and lift the cars up on top of their load with a primitive crane.

Can't imagine how they got them off, would have been just as interesting.

I was so concerned with what happens to cars during 'Roll on - Roll off' shipping that I chose to pay for a single enclosed shipping container for my GTR.

Was pretty expensive but worth every cent. Car left Japan perfect, and arrived the same way. When it arrived the underside of the car was still clean enough to eat off.

  • Like 1

I believe another reason would be - Stale fuel.

From port to port can take 2-3 weeks, even months. Why have a full tank of gas that would then need to be dropped anyway once at compliance.

I chose to pay for a single enclosed shipping container for my GTR.

Was pretty expensive but worth every cent.

How much did the enclosed container cost? B)

Was that a standard 20 foot container?

Did you needed to fasten the car to the container floor ?

I did use a Japanese car shipping estimate calculator for roll on roll off from jpy to perth about $1600 does that sound right? :huh:

A shipping container sounds so much safer,

But I just watched a show on TV last week they said 10,000 shipping container get lost at sea every year. :blink::unsure:

Edited by pol1on1

Did you needed to fasten the car to the container floor ?

I'm no expert but correct me if I'm wrong, this question kinda answers itself if you think about it.

It will go onto a ship.

And then have to swim along on this thing we call an ocean.

Hope and good will not hold it in place.

Hope and good will not hold it in place.

Well I hope you could mount the tyre straps but you can't in a container you have to use the inbuilt hook points now depending on where the car sits they might be upto 1mtr away I wouldn't want a dirty old strap going behind the wheel and then across the paint job.

So I was ask is their a special container with tyre tracks.

I should of edited my original question. :rolleyes:

  • Like 1

How much did the enclosed container cost? B)

Was that a standard 20 foot container?

Did you needed to fasten the car to the container floor ?

I did use a Japanese car shipping estimate calculator for roll on roll off from jpy to perth about $1600 does that sound right? :huh:

A shipping container sounds so much safer,

But I just watched a show on TV last week they said 10,000 shipping container get lost at sea every year. :blink::unsure:

Off the top of my head the shipping cost about 5k including container.

I think it was a 20 footer.

As for how the car was packed into the container and secured, I'm not sure on the details, but evidently they were extremely careful as the car is unmarked.

Not sure on the cost of 'Roll on - Roll off' shipping as i have not used this method.

Overall very happy with the care that was taken of my car :thanks:

-

  • Like 1

International Cargo Container

* ramps are placed inside the container lip

* width of car track is measured

* ramps are positioned accordingly - more to the left with a RHD coupe - more to the right with a LHD coupe

* ramps are strapped and tightened with ratchets

* car is driven on

* car is left in gear with handbrake on

* short axle straps with buckles at each end are placed over each axle

* each axle strap has a shackle going through both buckles and the attached long strap is tightened by a ratchet to a load-bearing bracket at the container's corner

* this is repeated at the other 3 corners and all straps run along the floor of the container

* wooden chocks are placed under each wheel

  • Like 2

My friend had a car shipped over in a container (R34 GTR M-SPEC NUR) and I can safely say I prefer roll on/roll off. Car came with quite a few scuffs due to the straps they used to secure it and the edge of the drivers door had a nice curve from them opening the door onto the container wall due to limited space.

Container is definately the safest option if you know care will be taken but almost usually its not. You have to remember how wide a car is and how wide a container is.

My friend had a car shipped over in a container (R34 GTR M-SPEC NUR)

You go through all that trouble getting a sea container only to have it damaged. that would bring a tear to eye to get a damaged M-SPEC NUR!!!!! :(

you just got to buy local if worried that much about damage, inspect what you buy get what you see

unless you go to japan and buy heaps of cotton wool and gladwrap it yourself but even then there’s always a...... (What If) :thumbsup:

From Terry's info, I wouldn't be interested in that method of container shipment, way too many things to go wrong.

I'd presumed (obviously incorrectly) that the cars were loaded and secured onto an RHS frame, 2-cars high and then the frame was pushed into the open end of the container.

Frame then secured to container and doors sealed.

Containers get rough treatment, far rougher than driving a car on/off the ship.

Must be thousands of these on youtube>

My mate sends his porsche RSR in a container at least twice a year to different countries to go racing. if it's fine for his car, it will be fine for yours

  • Like 2

By the same account, 99% of cars on the roads come in RoRo, and they are all fine.

Opportunity exists in either method for unscrupulous people to have their will with a car. Arseholes will arse, whatever the method.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...