Jump to content
SAU Community

Tyres For My M35 Axis Autech

ECR33_RB25DET
 Share

Recommended Posts

ECR33_RB25DET Community Regular

ECR33_RB25DET

Posted
Posted

Hey Guys,

Currently I have the NITTO INVO 235 40 18 fitted to the Axis Autech factory rims. It's nearing time to replace the tyres and I am looking at going Kumho 245 50 18 on the Axis rims.

Basically the current tyre profile simply makes the wheels look like skateboard wheels, they just don't fill the guards enough and look out of place.

It appears I have plenty of space to play with to accommodate 245 50 size tires.

Wondering what people are running, especially on their M35 Axis rims.

Also recommendations of very highly reputable places to have them fitted, balanced and wheel alignment done. No $hit in the past I've had tyre place leave the wheel nuts hand tightened only, not once, not twice but yes 3 times and across all 4 wheels.

post-72543-0-63049300-1423053767_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/453503-tyres-for-my-m35-axis-autech/
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

245/45/18 is a much better size than the 50 profile you're looking at. The 50 profile will have miles too much sidewall.

As a bonus; it is standard size for VE/VF Commodores, so prices a sensible, and they're easy to get.
It reduces the speedo error from around 9-10% to around 3%, which is also useful.

I'm running 245/45/18 Khumo KU31's and have done for years. They are quiet, wear well, and have good grip; wet and dry.

GoldZilla Grand Master

GoldZilla

Posted
Posted

Any recommendations where to score some KU31's at a good price?

The best advice I can give here is ring around everywhere (or at least everywhere you think you can trust, given the previous problems you've had), and specify the exact size, speed rating and weight details you require.

I'd also recommend Michelin Pilot Sport 3 tyres (if they're within your budget), I have them on my C34 and they're great!

Daleo Grand Master

Daleo

Posted
Posted

I buy them through a local tyre place, and they will match the Imported price on Australian stock. Which ends up about $200 per tyre fitted/balanced.

I've had both import and Australian delivered; I couldn't tell the difference.

Plenty of places on fleabay will freight them, but do the ring around; most of the time you can find them fitted/balanced locally for within a few dollars of freighting, then trying to get a shop to fit them for you.

Daleo Grand Master

Daleo

Posted
Posted

The only thing I'd criticise is the asymmetric nature of the MOMO tyre as compared to the KU31.

I tend to get an amount of camber wear on the inside edges of my tyres, and with the KU31's; I can have them flipped on the rims to get more wear from them.

Other than that, they seem to be a good thing.

http://www.sau.com.au/forums/topic/434880-momo-outrun-m3-tyres-has-anyone-tried-these/

Paramour Proficient

Paramour

Posted
Posted

Hello,

I had the Toyo Proxes 4 on my AXIS, they were fantastic and importantly had the right load rating, you will find that the AXIS is 630kg where as other mainstream is a bit lower. . 245/40ZR18 97W & 245/45ZR18 100W, if I recall didn't alter the rolling stock diameter too much. .

My 2 cents worth is Toyo Proxes 4 hands down. .

Jules

Daleo Grand Master

Daleo

Posted
Posted

They go ok Jules.

They're a 300 treadwear; I reckon I get better than 30,000km per set of 4.

I swap them front to rear every 10k and when the inner edges start to wear; I flip them on the rims.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...