Jump to content
SAU Community

Garrett Gt/gtx3076r Direct Bolt On For R34 Gtt?

Nismo34R

By Nismo34R,
in Engines & Forced Induction

 Share

Recommended Posts

Nismo34R Enthusiast

Nismo34R

Posted
Posted

Hey guys,

Time to rack everyone's brains!

I have been looking into a turbo upgrade recently for my GTT along with a few bits and pieces.. I have done a lot of research across the net, scoured through every possible thread on the forum trying to decide the way I want to go. Ideally I would like to keep the turbo set up low mounted with my factory manifold for the stealth look and keep that factoryish look with a black metal intake I will obviously have to fabricate. I already have a full exhaust from the 6 bolt JJR dump back to my kakimoto oval exhaust. I also want to run an internally gated setup.

I have looked into the HKS GTRS kits, hypergear range inc stao's highflow service, GCG highflow and the Garrett GT/GTX3076R

All of the above are a direct bolt on except for the garrett which I've found comes in a v-band or a 5 bolt rear. I was leaning towards the Garett's even though it meant changing/ fabricating the dump pipe.. I am aware the Garrett's need a 10 to 14 mm spacer aswell as it will foul on the factory manifold and also longer studs to get it bolted to the manifold. Thankyou research!

That was until I found this listing on ebay for a GT3076R which the seller has confirmed they are a direct fit and are a brand new unit with full factory warranty etc etc..For $100 extra the GTX variant can be provided.

http://m.ebay.com.au/itm/331086405044?nav=SEARCH

My question to my fellow SAU'ers.. Has anyone ever come across these before? Do any of you own one of these? As much as there is the chance I will need longer studs and spacers to get it fitted what would be the odds of this being a " direct bolt on " as claimed?

Thanks Pete..

GTSBoy Grand Master

GTSBoy

Posted
Posted

Well, it's obviously not a Garrett rear housing. They've knocked up a rear housing with Nissan dump flange and what would have to be enough extra length to push it away from the engine so it doesn't foul. That all sounds good.....but has anyone got any idea how good the profile in that housing is? Response? Power ceiling?

hypergear Grand Master

hypergear

Posted
Posted

^^

Using this turbine housing shown on photo above. The GT3076 CHRA will be straggling to perform any thing 250rwkws or above. Which our standard high flow service can easily out perform, and cost you less then half of their listed price.

  • Like 1
Kinkstaah Grand Master

Kinkstaah

Posted
Posted

Do the highflow because everything will bolt in... Because all the bolts are in the same spot.

That said I have a gtx3076r on the std manifold without a spacer, but as mentioned its not got a Garrett rear housing.

  • Like 1
Nismo34R Enthusiast

Nismo34R

Posted
  • Author
Posted

Do the highflow because everything will bolt in... Because all the bolts are in the same spot.

That said I have a gtx3076r on the std manifold without a spacer, but as mentioned its not got a Garrett rear housing.

Thankyou for the reply. So it seems it is a direct bolt on turbo! Do you mind me asking what power you are making and with what mods?

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

It's not really a bolt on turbo... Mine does NOT have a Garrett rear housing, it is a t3 with a vband rear on to a vband dump pipe.

I imagine due to that different rear housings is why I do not need a spacer.

statue Enthusiast

statue

Posted
Posted

I bought a similar "direct bolt on" Garrett from ebay. I got the GT2860RS version. It's possible I bought it off the same seller too, I'm not sure.

I tried installing it myself. It was direct bolt on, except for the oil and water lines. As said in their ad, you need to buy their line kit for extra $200

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • MBS206
      MAJOR FUEL ISSUES 25det neo r32

      By MBS206 · Posted

      Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...