Jump to content
SAU Community

32 & 33 Gtr Parts + Man Cave Stuff! - Brisbane

nuci_gtr
 Share

Recommended Posts

nuci_gtr Enthusiast

nuci_gtr

Posted
Posted

32 gtr veilside catback $400

3.5" stainless steel, jasma approved so not too loud. Couple of minor grazes but overall good nick

32 gtr stock front pipe and cat $50

Heat shields a bit scratched up but pipe itself is fine. No holes or dents.

32 gtr door cards $40

Average condition, can probably be repaired.

33 gtr HKS hi-power catback $300

3.5" stainless steel, good nick, fairly quiet but still gives a nice note on boost.

High flow cat $150

Near new, has had a flange cut off on one end but can easily have another one welded on. 3.5".

Rb26 engine covers $100

Stock colour, suit respray. No timing cover.

Oem 33 gtr floor mats $100

Full set, could do with a good steam clean. Decent nick.

Rb26 coilpacks $60

Came as spares with my 33 gtr, car was running splitfires so never needed to use them.

R33 a-pillar trim drivers side $20

Has screwhole from gauge pod, otherwise good nick.

R33 gtr oem wing $150

In KL0 silver, couple of minor marks otherwise good nick.

R33 gtr front and rear "gtr" badges $30 each or both for $50

R33 gtr Bilstein suspension $200

Shock and spring combo, non adjustable. Sits about an inch lower than stock. Can sms pics of car to show how it sat.

Vb vending machine $500

As new condition, about a metre tall, plays vb tune when you dispense a drink. Never used. Will take any cans as well as vb stubbies. Can sms pics.

Tooheys extra dry iPod dock + esky $250

Shaped like a big extra dry stubby, about a metre high, has iPod dock on top, speakers and strobe lights in the neck and hollow in the bottom for beers. Can sms pics.

Can post smaller items, otherwise pickup Brisbane northside. Best contact is on 0419 961 fivefivesix. Any dramas or if you're after pics just let me know and I can text them through. Will add items as I find them.

Cheers, Dan.

  • Like 1
Cheaboi Rookie

Cheaboi

Posted
Posted

May be interested in the R33 gtr Bilstein suspension If there still for sale?

Also its for my 97 stagea and from what i've read it should fit i was wondering if you could confirm this? And yeah sitting to low atm scraping too much.

nuci_gtr Enthusiast

nuci_gtr

Posted
  • Author
Posted

I couldnt tell you for sure if it'll fit mate, haven't had much to do with stageas before but I'm sure it'd be pretty easy to find out. I've got a bit of interest in them already but if you pm me your mobile number I'll get you some pics and keep you posted. Cheers.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...