Jump to content
SAU Community

Recommended Posts

Collecting suggestions and so far they are.

- Raise ride height to get LCAs back to parallel

- Increase camber to around -3.5 front and -2-2,5 rear
- Add adjustable caster arms and aim for around 5-6degrees (which will help camber also)
- Drop spring rates to 6/4.5.
- Return to stock swaybars.

A friend of mine who is running Tiens with 8/6 rates and similar bars has the above done (but is also running AD08R and in wider sizes) and his car is far more balanced.

Thoughts?

Probably not bad. The amount of camber that is good for you will of course depend somewhat on the tyre you're running.

I wouldn't be afraid the keep the big ARBs if you back off the spring rates.

The other thing you need to put in your list is my first suggestion, to add some bloody damping back into the suspension!

Looking at your setup, it seems like you have a really thick rear swaybar compared to what you have at the front

Looking at the Whiteline s13 swaybar sizes:

They have 27mm front and 22/24mm rear

Currently you are running 26mm (softest) front and 25mm rear

Generally on the s-chassis, you would want to set the front to full hard (for swaybar) and tune the rear to suit

In regards to the lower control arm, as long as you have it parallel to the ground, it will be sufficient and roll center do not suffer

I run -2.5 front, 7 degree castor and -2 rear 1mm toe in if that helps

Plenty of grip however i also run 245/255 tyre size

I am running 27mm front, softest setting, and 25mm hollow gtr rear, which roughly equates to 19-22mm solid I read. The whiteline rear bars are solid. So stiffer again.

Thanks for info.

Interesting about your comment re hardest front as I imagine that would cause it to understeer more.

27mm is the middle bolt on the swaybar, when you soften it, it means it's -1 mm so it means you're running 26mm ;)

Your older video, is that on brand new tyres? And how long have you had these tyres for?

Collecting suggestions and so far they are. [/size]- Raise ride height to get LCAs back to parallel[/size]

- Increase camber to around -3.5 front and -2-2,5 rear

- Add adjustable caster arms and aim for around 5-6degrees (which will help camber also)

- Drop spring rates to 6/4.5.- Return to stock swaybars.

A friend of mine who is running Tiens with 8/6 rates and similar bars has the above done (but is also running AD08R and in wider sizes) and his car is far more balanced.

Thoughts?

-3.0 to -3.5 on the front -1.5 on the rear.

Yes to castor arms, I think mine is around 6 degrees maxed out

Forget changing spring rates, mine are tein monoflex 8/6 and are fine. Play with the dampening. I wind my fronts to about 90% hard, rears 30%

Toe has already been mentioned- the 1mm mark is about right.

Don't return to stock sways, just drop the link of the rear bar altogether and see how that goes.

Also, have the car corner weighted if not done already. Winding heights up and down can really stuff up the balance.

I'll post a vid of my 180 at the track for ..... Science!

Much better tyres than mine.

Most of the advice in getting about more camber or harder dampers is from people running much wider and grippier tyres so I'm in too minds about how much it applies to me.

The tyres are shot honestly, they are hard as. They measure 235/45 in the conventional sense. Michelin just decides to put more number on them.

I've got 235/45 RSRs as well. They are on my road wheels, and I've tracked them too. They aren't awesome but they don't suck. What your struggling for is balance in my eyes. Your front end is out performing the rear end. So you need to increase the rear grip, and limit the front ends impact.

At the end of the day it doesn't matter what tyres you run, having the car setup to extract the maximum grip from whatever is available in the tyre is the goal.

It would be worth sending the car to a suspension tuning workshop with track car experience and explaining what your feeling on the track.

Running harder damping has nothing to do with the tyres though. It's all about making sure the damping is sufficient for the springs.

Let's put it this way. You used to run softer bars and needed the dampers wound down to make it work. You've added spring rate through stuffer bars and now it's not happy, with your description of how it drives sounding like it's underdamped. Therefore, potential solution is to add damping.

The front-rear balance stuff is a whole 'nother issue. As is changing camber. Adding roll stiffness to the chassis can actually well require you to add camber anyway, so it is definitely something that might need a tweak as part of the exercise. If any of the other advice makes you go faster, then you are going to need more camber.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
    • FYI: Racebox RE7R Custom Tunes Released!   https://goracebox.com/.../2017-infiniti-q50-q60-re7r-tcm...   FOR GEN 2 (21+) VEHICLES, PLEASE SEE NOTE AT BOTTOM See more   But whomever tuned your car is the tuner you should go back to, AMS, Sonictune or BT Tune....
×
×
  • Create New...