Jump to content
SAU Community

Recommended Posts

They look insane.

$55k drive away is a bargain too. Got two years to run on my current lease. The RS will be a strong contender for a replacement then.

Can't wait for Chris Harris to test it.

  • Like 1

But do these things have Ford's dual clutch transmission?

So many complaints from everyday drivers.

Not such a problem if the car is pushed hard where the transmission can correctly predict the next gear.

St is manual only. And FYI the dual clutch transmission problems in the normal focus have now been solved. The issue was an incorrectly fitted transmission seal leaking onto the clutches causing excessive shudder and slipping. Ford has been replacing the contaminated clutches and seals as required. They know behave quite well. Still have very little occasional low speed shudder but acceptable. My wife owns a focus and we have gone through the above. We're now quite happy.

Good news that Ford has finally acknowledged there was a problem, took long enough.

Many dissatisfied owners will never trust that company again, but then it's pretty much the same story from the rest too.

What amazes me is these car companies jumping onto the twin clutch band wagon when some can't even get a single working properly.

You'd think after 100 years that the old dry plate clutch would be trouble free.

Good news that Ford has finally acknowledged there was a problem, took long enough.

Many dissatisfied owners will never trust that company again, but then it's pretty much the same story from the rest too.

What amazes me is these car companies jumping onto the twin clutch band wagon when some can't even get a single working properly.

You'd think after 100 years that the old dry plate clutch would be trouble free.

Yeah, it was a quiet acknowledgement. Handing clutch control to a computer system sounds good in theory but hey, so did communism lol. Mass producing manufacturers hold out on admitting a fault or problem for as long as they can for reasons I don't understand. The only thing that makes any sense in that case is if they don't know what the actual problem is.

Back on topic. The st is manual only and is a cracker of a car. The coming RS can only be better, you would think. AWD and a drift mode button. Hmmm, much want. If only the wife could /would drive a manual.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hell, I'm sufficiently wary of the ZSS suspension arms, let alone something like a hub.
    • Got it back home and got started pulling the hub off and diagnose the issue. Axle was stuck after removing the 36mm nut so i used a 3 jaw puller to try and push it out and... eH5FXvJ8.mp4   spend the next few hours trying to remove the axle from the remaining hub as it was very much jammed in there when the spindle sheared off. resulting damage as below R53AIy6 - Imgur.mp4   Looks like the was already a stress fracturing in the spindle as can be seen with the darker cracked section My working theory is maybe when the pinion gear exploded last year the shock put through the hub was the initial crack. Then a few events later it finally let go. Just lucky it happened where it did and not 190km/h on the next sweeper or into the hairpin The bearing/hub assembly went in in 2019 and were non-genuine "ZSS" assemblies and no nails were harmed in the process. #BreakHubsNotNails
    • Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
×
×
  • Create New...