Jump to content
SAU Community

Recommended Posts

Hi all,

Bought the car but have my own setup to replace this package. Fresh, no track work. Tuned by unigroup built by west end

Engine

Fresh build by west end performance (only run-in and tuned) 86.5mm CP pistons

Manley rods

arp2000 rod bolts

linished r34 crank.

full supertech head with 1mm oversized valves.

Ports cleaned up.

brand new -5 turbos.

Comes with standard sump

No oil pump (setup for dry sump)

hks cam gears

tomei poncams (260 degree 9.15mm lift).

twin hks pod filters

hks dump pipes

$9k

Gearbox

Looks to me like a Yokohama auto gallery box.

Had one in the past, essentially a os gearset. Completely overhauled by Mark berry and Includes multiplate clutch

$4k

Is the box a 5 or 6 speed? Straight cut or helical? Ratios? Kms since overhaul?

5 speed, helical cut.

Kms - not sure (a couple of track days I belive) have receipts for overhaul new syncros

Ratios unknown (I'll confirm with previous owner)

Jim berry clutch (I'll confirm whether it's a single or twin)

Ahh ok. Im running 430awkw on a conservative tune with plenty left to go.

Also looking for something for a bit of track use.

Might need something with straight cut gears.

Engine build receipt comes to $4100

Ah k I get you. Not so much interested in a receipt for the cost, more as proof / itemisation of what was done in the build.

  • 3 weeks later...
  • 1 month later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...