Jump to content
SAU Community

Recommended Posts

My Box of Things Sale, R34, 180sx, V35, RB20, SR, CA. Located in Tascott NSW 2250

Willing to Post, Pictures Available, Msg 04049212eight Seven or PM

R34 Stuff

R34 standard filter box bottom half only $10
R34 Standard Arms $Free
R34 GTT stockies $150
R34 Dash $50
R34 GTT Spoiler $80
R34 Coupe doors $50 each

R34 interior trim pieces $20 each

R34 Viscous Diff Centre $50

R34 Standard Gauges $60

R34 Rear Hicas Module $40

180sx Stuff
Sr/Ca gear stick/knob/plate $10
CA Manifold $10
180sx Black tail lights $100
180sx headlights $50
180sx pig nose front bumper $150
180sx rear bumper $50
Ca/Sr non abs tailshaft $50
Sr 20 carbon pod filter Cover $20
Ca18 a/c compressor $20

5 Bolt Dump pipe into 3 bolt $40

S14 Standard Fuel Pump Assembly $5

Rb20 engine complete in bits all parts available $125 for the lot

V35 Stuff
V35 Front Bar $250
V35 Rear Bar $250

Universal Parts

1x 18x8 +42 and 1x 18x9 +33 PDW Replay no tyres $20 each

New Nos Pod filter $5
Malpassi FPR $20

Intercooler 600x300x76 3” in/out $100

Hi there,

I'm after the following if you have any?

- GTR front lip

- GTR wing (must be genuine, 3pc wing. not fibreglass shit, got one alrdy!)

- RB20 coilpack cover. Prefer factory ones but will consider tidy aftermarket ones that cops will take nicely to!

Located south east Victoria, so will require shipping.

Sorry only have 5 RB20 coilpacks as I dropped one and the plug part broke so I just put it in my bin. coilpacks work just fine but I've upgraded to splitfires.

5 Coilpacks $30

  • 9 months later...
  • 3 weeks later...

My Box of Things Sale, R34, 180sx, RB20, RB25, S15, R32, SR, CA. Located in Tascott NSW 2250

Willing to Post, Pictures Available, Msg 04049212eight Seven or PM

R34 Stuff

R34 standard filter box bottom half only $10

R34 Dash $50

R34 GTT Spoiler $80

R34 Coupe doors $50 each

R34 interior trim pieces $20 each

R34 Viscous Diff Centre $50

R34 Standard Gauges $60

R34 Rear Hicas Module $40

R34 Stock Turbo Manifold $30

R34 5 Bolt Drive Shafts $100

R34 5 Bolt Diff Half Shafts $50

180sx Stuff

Sr/Ca gear stick/knob/plate $10

CA Manifold $10

180sx Black tail lights $100

180sx headlights $50

180sx rear bumper $50

Ca18 a/c compressor $20

5 Bolt Stainless Dump pipe into 3 bolt $40

S15 Front Brake Rotors Machined and Sealed $50

R32 AWD RB20DET ECU $50

Updated 28/03/2016

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...